Unanswered topics | Active topics


Board index » »

All times are UTC-06:00



Post new topic  Reply to topic  Page 1 of 2
  [ 18 posts ] 
  Previous topic | Next topic 
Author Message
corsair
PostPosted: Thu Jan 25, 2007 3:36 pm 
Offline

Joined: Tue Feb 14, 2006 2:01 pm
Posts: 75
Location: Germany
Image

EDIT: you can grab the newest netboot images here (when there will be newer ones): http://dev.gentoo.org/~corsair/efika/

Hello,

I've just created a fresh netboot image for my efika and I would like to share it with you 8)

note 1: nothing is tweaked and things aren't working as they should. only basic setup is done right now :roll:

note 2: I have defaulted the console output to ttyPSC0, so if you are using a graphics card then you have to place the correct console= option to the kernel (I think so.. I cannot try though)...

follow this steps, if you want to try it out:

1. Grab the image from here: http://dev.gentoo.org/~corsair/efika/efika_20070125.img

2. setup a tftp server and make the image accessable
Code:
$ emerge atftp
$ mkdir /tftroot/
$ /etc/init.d/atftp start
$ cp /path/to/efika_20070125.img /tftproot/efika.img
$ chown -R nobody:nobody /tftroot/
3. boot your efika with this command:
Code:
ok boot eth:the.ip.add.res,efika.img
in my case:
Code:
ok boot eth:192.168.0.2,efika.img
4. be happy :wink:

5. grab a gentoo stage and install it to your hard disk :-D



I'll tweak the image when I've some spare time again.

Thanks to the folks from debian who have created the mkvmlinuz tool, which made this so painless.

regards,

-corsair



Code:
EFIKA 5K2 Boot Strap [RELEASE BUILD] (c) 2002-2006 bplan GmbH (BUILD 20061101134833)
Running on CPU PVR: 0x80822014
Running on system SVR: 0x80110022
BIOS Code position: 0xFFF040D0
Setup System Config... Done.
Setup Memory Config... Done.
Setup PCI... Done.
Setup ATA... Done.
Setup USB... Done.
Setup ETH... Done.
Memory Test skipped (Warmboot detected)
cpu0: PowerPC,G2 CPUClock 396 Mhz BUSClock 132 Mhz (Version 0x8082,0x2014)
channel 0 unit 0 : ata | IC25N020ATCS05-0 | CS2OA61A
ATA device not present or not responding
Welcome to SmartFirmware(tm) for bplan EFIKA5K2
Version 1.3 (20061107101950)
SmartFirmware(tm) Copyright 1996-2001 by CodeGen, Inc.
All Rights Reserved.
Pegasos BIOS Extensions Copyright 2001-2006 by bplan GmbH.
All Rights Reserved.
ok boot eth:192.168.0.2,efika.img

zImage starting: loaded at 0x00400000 (sp: 0x017ffe90)
Allocating 0x325c54 bytes for kernel ...
OF version = 'EFIKA5K2,1.3'
Allocating 0xe56b2 bytes for initrd ...
initial ramdisk moving 0x1b26000 <- 0x571000 (0xe56b2 bytes)
initrd head: 0x1f8b0808
gunzipping (0x1800000 <- 0x407000:0x5709ef)...done 0x304564 bytes
OF stdout device is: /failsafe
command line: root=/dev/ram rw console=ttyPSC0 panic=10
memory layout at init:
alloc_bottom : 01c0c000
alloc_top : 30000000
alloc_top_hi : f000c000
rmo_top : 30000000
ram_top : f000c000
Looking for displays
instantiating rtas at 0x07ffb000 ... done
copying OF device tree ...
Building dt strings...
Building dt structure...
Device tree strings 0x01c0d000 -> 0x01c0d6cd
Device tree struct 0x01c0e000 -> 0x01c10000
Calling quiesce ...
returning from prom_init
Using Efika machine description
Only using first contiguous memory region<5>Linux version 2.6.19.1-efika (root@powerbook) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #10 We7
Found initrd at 0xc1b26000:0xc1c0b6b2
Efika: PCI bus 0 controlled by /pci@80000000

Zone PFN ranges:
DMA 0 -> 32768
Normal 32768 -> 32768
early_node_map[1] active PFN ranges
0: 0 -> 32768
Built 1 zonelists. Total pages: 32512
Kernel command line: root=/dev/ram rw console=ttyPSC0 panic=10
MPC52xx PIC: MPC52xx PIC Remapped at 0xf0000500
MPC52xx PIC: MPC52xx SDMA Remapped at 0xf0001200
MPC52xx PIC is up and running!
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 125652k/131072k available (2712k kernel code, 5268k reserved, 256k data, 131k bss, 156k init)
Mount-cache hash table entries: 512
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 917k freed
NET: Registered protocol family 16
Efika : Added pic@f0000500 (type 'interrupt-controller' at '/builtin@F0000000/pic@F0000500') to the known devices
Efika : Added bestcomm@f0001200 (type 'dma-controller' at '/builtin@F0000000/bestcomm@F0001200') to the known devices
Efika : Added sram@f0008000 (type 'memory' at '/builtin@F0000000/sram@F0008000') to the known devices
Efika : Added ata@f0003a00 (type 'ata' at '/builtin@F0000000/ata@F0003A00') to the known devices
Efika : Added usb@f0001000 (type 'usb' at '/builtin@F0000000/usb@F0001000') to the known devices
Efika : Added ethernet@f0003000 (type 'network' at '/builtin@F0000000/ethernet@F0003000') to the known devices
Efika : Added sound@f0002200 (type 'sound' at '/builtin@F0000000/sound@F0002200') to the known devices
Efika : Added serial@f0002000 (type 'serial' at '/builtin@F0000000/serial@F0002000') to the known devices
Efika : Added pcidma@f0003800 (type 'dma-controller' at '/builtin@F0000000/pcidma@F0003800') to the known devices
PCI: Probing PCI hardware
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 4096 bind 2048)
TCP reno registered
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
Serial: MPC52xx PSC UART driver
serial@f0002000: ttyPSC0 at MMIO 0xf0002000 (irq = 129) is a MPC52xx PSC
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
MPC52xx/OpenFirmware: 13696 kB of free SRAM
eth0: Phy @ 0x10, type GENERIC (0x00008201)
ata: MPC52xx IDE/ATA libata driver
ata1: PATA max PIO4 cmd 0x0 ctl 0xC9012A5C bmdma 0x0 irq 135
scsi0 : mpc52xx_ata
ata1.00: ATA-5, max UDMA/100, 39070080 sectors: LBA
ata1.00: ata1: dev 0 multi count 0
ata1.00: configured for PIO4
scsi 0:0:0:0: Direct-Access ATA IC25N020ATCS05-0 CS2O PQ: 0 ANSI: 5
SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 39070080 512-byte hdwr sectors (20004 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
ppc-of-ohci usb@f0001000: USB Host Controller
ppc-of-ohci usb@f0001000: new USB bus registered, assigned bus number 1
ppc-of-ohci usb@f0001000: irq 134, io mem 0xf0001000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
i8042.c: No controller found.
mice: PS/2 mouse device common for all mice
IPv4 over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 156k init
init started: BusyBox v1.2.2 (2007.01.25-21:08+0000) multi-call binary

efika login: root
Password:
~ # ls -l
~ # ls /
bin home lost+found root usr
dev lib mnt sbin var
etc linuxrc proc tmp
~ # ls / -l
drwxr-xr-x 2 root 0 2048 Jan 25 21:12 bin
drwxr-xr-x 3 root 0 1024 Jan 25 22:25 dev
drwxr-xr-x 4 root 0 1024 Jan 25 21:27 etc
drwxr-xr-x 2 root 0 1024 Jan 25 21:12 home
drwxr-xr-x 2 root 0 1024 Jan 25 21:12 lib
lrwxrwxrwx 1 root 0 11 Jan 25 21:28 linuxrc -> bin/busybox
drwx------ 2 root 0 12288 Jan 25 21:28 lost+found
drwxr-xr-x 2 root 0 1024 Jan 25 21:12 mnt
dr-xr-xr-x 36 root 0 0 Jan 25 22:25 proc
drwxr-xr-x 2 root 0 1024 Jan 25 21:21 root
drwxr-xr-x 2 root 0 1024 Jan 25 21:12 sbin
drwxrwxrwt 2 root 0 1024 Jan 25 21:01 tmp
drwxr-xr-x 3 root 0 1024 Jan 25 21:12 usr
drwxr-xr-x 7 root 0 1024 Jan 25 21:12 var
~ # uname -r
2.6.19.1-efika
~ #


Last edited by corsair on Sun Jan 28, 2007 1:35 pm, edited 1 time in total.

Top
   
Reply with quote  
corsair
 Post subject:
PostPosted: Thu Jan 25, 2007 3:51 pm 
Offline

Joined: Tue Feb 14, 2006 2:01 pm
Posts: 75
Location: Germany
heh.. I was just lying in bed, closing my eyes and then I mentioned.... I forgot to tell everyone the root password ^^

the root password is: gentoo

regards,

corsair
Top
   
Reply with quote  
SoundSquare
 Post subject:
PostPosted: Fri Jan 26, 2007 2:57 am 
Offline

Joined: Sun May 08, 2005 8:46 pm
Posts: 559
Location: Paris
@corsair

well done ! sounds like a painless way to install Gentoo on Efika, i'll try that later this weekend.
thanks !
Top
   
Reply with quote  
corsair
 Post subject:
PostPosted: Fri Jan 26, 2007 4:31 am 
Offline

Joined: Tue Feb 14, 2006 2:01 pm
Posts: 75
Location: Germany
Quote:
@corsair

well done ! sounds like a painless way to install Gentoo on Efika, i'll try that later this weekend.
thanks !
thanks. Even if I don't know if it's possible to install gentoo with this image yet ^^ I'll try to chroot into my existing gentoo installation on the hard disk this evening.

I actualy grabbed the first busybox config I found, so I don't even know if fdisk is available.

I'll definetly integrate some udev foo; parted; a fancy motd; filesystem tools for reiserfs 3 (or even reiserfs 4), ext3 (maybe even ext4) and xfs.

After that my focus would be on applications like irssi and such. well.. I'll see what is possible with netboot and what would make a *huge* image...

regards,

-corsair
Top
   
Reply with quote  
teme
 Post subject:
PostPosted: Sat Aug 04, 2007 3:20 pm 
Offline

Joined: Thu Aug 02, 2007 12:56 pm
Posts: 9
Hi,

Could you post your kernel configuration? I am trying to get initramfs to work but I am not sure how the kernel should be configured so that rootfs cpio would be embedded into kernel image.
Top
   
Reply with quote  
corsair
 Post subject:
PostPosted: Sun Aug 05, 2007 12:57 am 
Offline

Joined: Tue Feb 14, 2006 2:01 pm
Posts: 75
Location: Germany
yes, I also needed some time to figure out how to embed the root file system in the image. take a look here:

http://packages.debian.org/unstable/devel/mkvmlinuz

That great piece of software combines the kernel and the rootfs.

If you still need the kernel config, I'll upload it somewhere.
Top
   
Reply with quote  
teme
 Post subject:
PostPosted: Sun Aug 05, 2007 3:52 am 
Offline

Joined: Thu Aug 02, 2007 12:56 pm
Posts: 9
Quote:

That great piece of software combines the kernel and the rootfs.
Yes, I managed to bring those two suckers together :)

Anyway, even that initramfs seems to be extraced, rootfs is not mounted.

Code:
Using Efika machine description
Only using first contiguous memory region<5>Linux version 2.6.19-rc6-stripped (teemu@nipsu) (gcc version 4.1.0) #14 Sun Aug 5 11:37:41 EEST 2007
Found initrd at 0xc1a7f000:0xc1a7f086
Efika: PCI bus 0 controlled by /pci@80000000

Zone PFN ranges:
DMA 0 -> 32768
Normal 32768 -> 32768
early_node_map[1] active PFN ranges
0: 0 -> 32768
Built 1 zonelists. Total pages: 32512
Kernel command line: console=ttyPSC0,115200 panic=3 root=/dev/root
MPC52xx PIC: MPC52xx PIC Remapped at 0xf0000500
MPC52xx PIC: MPC52xx SDMA Remapped at 0xf0001200
MPC52xx PIC is up and running!
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 127228k/131072k available (2120k kernel code, 3680k reserved, 216k data, 99k bss, 124k init)
Mount-cache hash table entries: 512
Unpacking initramfs... done
Freeing initrd memory: 0k freed
NET: Registered protocol family 16
Efika : Added pic@f0000500 (type 'interrupt-controller' at '/builtin@F0000000/pic@F0000500') to the known devices
Efika : Added bestcomm@f0001200 (type 'dma-controller' at '/builtin@F0000000/bestcomm@F0001200') to the known devices
Efika : Added sram@f0008000 (type 'memory' at '/builtin@F0000000/sram@F0008000') to the known devices
Efika : Added ata@f0003a00 (type 'ata' at '/builtin@F0000000/ata@F0003A00') to the known devices
Efika : Added usb@f0001000 (type 'usb' at '/builtin@F0000000/usb@F0001000') to the known devices
Efika : Added ethernet@f0003000 (type 'network' at '/builtin@F0000000/ethernet@F0003000') to the known devices
Efika : Added sound@f0002200 (type 'sound' at '/builtin@F0000000/sound@F0002200') to the known devices
Efika : Added serial@f0002000 (type 'serial' at '/builtin@F0000000/serial@F0002000') to the known devices
Efika : Added pcidma@f0003800 (type 'dma-controller' at '/builtin@F0000000/pcidma@F0003800') to the known devices
PCI: Probing PCI hardware
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 4096 bind 2048)
TCP reno registered
io scheduler noop registered (default)
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
Serial: MPC52xx PSC UART driver
serial@f0002000: ttyPSC0 at MMIO 0xf0002000 (irq = 129) is a MPC52xx PSC
MPC52xx/OpenFirmware: 13664 kB of free SRAM
i8042.c: No controller found.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
eth0: Phy @ 0x10, type GENERIC (0x00008201)
NET: Registered protocol family 17
No filesystem could mount root, tried:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
<0>Rebooting in 3 seconds..
I am also not sure about kernel parameters in case of initramfs.

EDIT: some typos
Top
   
Reply with quote  
corsair
 Post subject:
PostPosted: Sun Aug 05, 2007 8:06 am 
Offline

Joined: Tue Feb 14, 2006 2:01 pm
Posts: 75
Location: Germany
root=/dev/root is wrong. Try to set "Kernel options --> Default bootloader kernel arguments" to:
Code:
root=/dev/ram rw console=ttyPSC0 panic=3
Top
   
Reply with quote  
teme
 Post subject:
PostPosted: Sun Aug 05, 2007 8:31 am 
Offline

Joined: Thu Aug 02, 2007 12:56 pm
Posts: 9
Tried that and still got:
Code:
No filesystem could mount root, tried:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0)
<0>Rebooting in 3 seconds..
Top
   
Reply with quote  
nixnut
 Post subject:
PostPosted: Sun Aug 05, 2007 10:19 am 
Offline

Joined: Mon Mar 27, 2006 12:16 pm
Posts: 79
try root=/dev/ram0
Top
   
Reply with quote  
teme
 Post subject:
PostPosted: Mon Aug 06, 2007 10:17 am 
Offline

Joined: Thu Aug 02, 2007 12:56 pm
Posts: 9
Quote:
try root=/dev/ram0
Did not work either :cry:
Top
   
Reply with quote  
teme
 Post subject:
PostPosted: Mon Aug 06, 2007 11:38 am 
Offline

Joined: Thu Aug 02, 2007 12:56 pm
Posts: 9
Hey!

Found the problem! I was accidentally removed bin/busybox from my rootfs and /init was linked agains it so the kernel was not able to execute /init.

By restoring the /bin/busybox I was able to boot the system.
Top
   
Reply with quote  
corsair
 Post subject:
PostPosted: Fri Nov 30, 2007 12:46 pm 
Offline

Joined: Tue Feb 14, 2006 2:01 pm
Posts: 75
Location: Germany
http://dev.gentoo.org/~corsair/efika/efika_20071130.img

this is a new netboot image. it's based on 2.6.24-rc3-git5. It should include fdisk and everything that's needed to install gentoo.

Unfortunately I'm unable to get network running. ifconfig eth0 up works, but ping/wget/etc does not work... can someone give me a hint?
Top
   
Reply with quote  
PurpleAlien
 Post subject:
PostPosted: Fri Nov 30, 2007 1:19 pm 
Offline
Genesi

Joined: Mon Jan 30, 2006 2:28 am
Posts: 409
Location: Finland
Hi.

Could it be the efika.forth Firmware patch that is needed:
http://www.powerdeveloper.org/platforms ... devicetree

This should be needed for the new Ethernet driver.

Johan.

_________________
Johan Dams, Genesi USA Inc.
Director, Software Engineering

Yep, I have a blog... PurpleAlienPlanet
Top
   
Reply with quote  
corsair
 Post subject:
PostPosted: Fri Nov 30, 2007 4:39 pm 
Offline

Joined: Tue Feb 14, 2006 2:01 pm
Posts: 75
Location: Germany
thanks! that fixed it. I didn't recognized that the efika 'forgets' the new device tree, when you press the reset button!

Tomorrow I'll test, if I can do a full install on the machine, or if there are packages missing.

EDIT: It should be able to use the image from a USB drive, too. Just place it and the efika.forth on the drive, 'execute' the efika.forth start the image.
Top
   
Reply with quote  
Display posts from previous:  Sort by  
Post new topic  Reply to topic  Page 1 of 2
  [ 18 posts ] 

Board index » »

All times are UTC-06:00

Who is online

Users browsing this forum: No registered users and 6 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
PowerDeveloper.org: Copyright © 2004-2012, Genesi USA, Inc. The Power Architecture and Power.org wordmarks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org.
All other names and trademarks used are property of their respective owners. Privacy Policy
Powered by phpBB® Forum Software © phpBB Group