All times are UTC-06:00




Post new topic  Reply to topic  [ 6 posts ] 
Author Message
 Post subject: Welcome LabVIEW
PostPosted: Fri May 25, 2007 7:48 am 
Offline
Genesi

Joined: Fri Sep 24, 2004 1:39 am
Posts: 1422
We initiate a new Forum today around LabVIEW. Check it out:

Image

LabVIEW

How would you like to use LabView with the EFIKA/Open Client?

Best regards,
R&B :)

_________________
http://bbrv.blogspot.com


Top
   
 Post subject:
PostPosted: Fri May 25, 2007 8:48 am 
Offline

Joined: Thu Jul 28, 2005 12:41 am
Posts: 1066
I started my PhD chemistry lab project on a PC with Labview. Back at the time there was just one measurement equipment to drive. Then came the idea to change to EFIKA and use FreePascal / Lazarus for cross platform development. Now, with eight units of the measurement equipment running in parallel, Pascal starts to show its limits. With LabView Embedded running on EFIKA, it's the best time to return to LabView. Some of the many benefits:
  • * easy, graphical programming
    * a lot more precise timing, than in Pascal

_________________
CzP
http://czanik.blogs.balabit.com/


Top
   
 Post subject:
PostPosted: Fri May 25, 2007 12:58 pm 
Offline
Genesi

Joined: Mon Jan 30, 2006 2:28 am
Posts: 409
Location: Finland
Hi.

The way I want to use LabVIEW is in an attempt to make motor control (e.g., PID) easier for students to analyze and measure.

The idea is to use LabView with in our RoboCup project (http://robotics.puv.fi) and to create an analysis tool to improve the motion control of the robot based on a variety of parameters.

For example, we want to see if we can still have reliable control (at less then optimal performance of course) somehow when the battery is close to being depleted. The robot still moves at this time, but not reliably. With LabVIEW we can see what really goes on at this stage.

The set-up for this testing environment will be based on an EFIKA with custom designed PCI card which allows a multitude of motors to be connected. This whole system is then connected to a LabVIEW application which can do the measurements and analysis. The reason for using the PCI card on the EFIKA and not on a PC is because the future version of the robot will run on an EFIKA derivative. That way, we can use the final platform already today to develop all the software on.


This is only one concrete example I would like to have here at the University. Others include a whole range of process control setups with EFIKA's taking care of measuring sensor data (even in a sensor network), with the LabVIEW software gathering and analyzing this data.
To speed development up, LabVIEW Embedded can be used on the EFIKA to make life a whole lot easier.
There are many areas where a set-up like that would be very useful, and we believe that a co-operation with the companies in our area could get good results and practical implementations.


Johan.

_________________
Johan Dams, Genesi USA Inc.
Director, Software Engineering

Yep, I have a blog... PurpleAlienPlanet


Last edited by PurpleAlien on Fri May 25, 2007 1:52 pm, edited 1 time in total.

Top
   
 Post subject: Re:LabVIEW Embedded
PostPosted: Fri May 25, 2007 12:58 pm 
Offline

Joined: Fri May 25, 2007 12:00 pm
Posts: 5
Location: Austin, TX
Thanks for the kind words.

LabVIEW Embedded is being used in lots of applications from medical devices to underwater monitoring systems to digital print kiosks.

I am actually working on adding support for the NI USB-6009 (http://sine.ni.com/nips/cds/view/p/lang/en/nid/14603) to the EFIKA so I can add some low cost/high quality analog I/O. I'll keep you posted on my progress.

P.J.
National Instruments


Top
   
 Post subject:
PostPosted: Sat May 26, 2007 1:05 am 
Offline

Joined: Thu Jul 28, 2005 12:41 am
Posts: 1066
First of all, thank you for making the EFIKA platform even more fun! And I also have a couple of questions about the LabView EFIKA port:

- Will this driver also work with the 6008 (what I have now over here)?

- Will simple serial port communication be supported? That is what I use now most of the time, a custom device on a serial port.

_________________
CzP
http://czanik.blogs.balabit.com/


Top
   
 Post subject:
PostPosted: Tue May 29, 2007 7:55 am 
Offline

Joined: Fri May 25, 2007 12:00 pm
Posts: 5
Location: Austin, TX
Hi Peter,

Yes, the port should also work with the NI USB-6008, and I will be sure to test it. I haven't tested the serial port, but it will most likely be supported as well. I'll keep you posted.

Thanks!
P.J.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 6 posts ] 

All times are UTC-06:00


Who is online

Users browsing this forum: No registered users and 7 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
PowerDeveloper.org: Copyright © 2004-2012, Genesi USA, Inc. The Power Architecture and Power.org wordmarks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org.
All other names and trademarks used are property of their respective owners. Privacy Policy
Powered by phpBB® Forum Software © phpBB Group