It is just initializing, but it is something!
=======
From: Joshua Uziel
Date: May 30, 2006 9:31:51 PM CDT
To: Raquel Velasco and Bill Buck
Cc: Tom Riddle, Sven Luther
Subject: Re: screenshot
Attached is a boot log and a binary to take a look at. It doesn't do too much. All you should have to do is make an entry in the boot menu to load and execute it. Let me know if you have any questions.
PegasosII Boot Strap (c) 2002-2004 bplan GmbH
Running on CPU PVR:80020101
Enable L1 ICache... Done.
Clean/Flush Block enabled
Reading W83194 : 00FFFFFFFFFF0000 Done.
Setting Front Side Bus to 133MHz... Done.
Memory has not changed
Configuring Memory
Memory Config Done
Configuring PCI0... Done.
Configuring PCI1... Done.
Configuring ETH... Done.
Releasing IDE reset ... Done.
Configuring Legacy Devices
Initializing KBD...00000032 FAILED.
Testing 10000000 Bytes, Pass: 00000000 Failed: 00000000
RAM TEST (fill random)... Done.
SmartFirmware:
cpu0: PowerPC,74x7 CPUClock 999 Mhz BUSClock 133 Mhz (Version 0x8002,0x0101)
no/bad nvramrc - performing default startup script
ATA device not present or not responding
ATA device not present or not responding
channel 0 unit 0 : ata | ST340014A | 3.06
ATA device not present or not responding
channel 1 unit 0 : atapi | SAMSUNG CDRW/DVD SM-352F | T900
EMULATION INT HANDLER ENTERED WITH:
INT NO: 15
EAX=0003 EBX=1111 ECX=2222 EDX=3333 ESP=0000 EBP=5555 ESI=6666 EDI=7777
AX=4E08 BX=C505 CX=0003 DX=102A SP=6CAA BP=5555 SI=6CB8 DI=9C58
DS=C000 ES=BAD0 SS=C000 CS=F000 IP=FE15 NV UP -- PL ZR NA PE NC
CS:IP = F4 FS=BAD4 GS=BAD5C558 C000 0244 3000 0000 01B4 AC63 0200
UNHANDLED INT 10 FUNCTION 0007 WITHIN EMULATION
VM using 4782891 x86 cycles for GFX init
Welcome to SmartFirmware(tm) for bplan Pegasos2 version 1.2 (20040810112413)
SmartFirmware(tm) Copyright 1996-2001 by CodeGen, Inc.
All Rights Reserved.
Pegasos BIOS Extensions Copyright 2001-2004 by bplan GmbH.
All Rights Reserved.
auto-booting...
Auto-boot in 5 seconds - press ESC to abort, ENTER to boot: Auto-boot in 5 seconds - press ESC to abort, ENTER to boot: Auto-boot in 4 seconds - press ESC to abort, ENTER to boot: Auto-boot in 3 seconds - press ESC to abort, ENTER to boot: Auto-boot in 2 seconds - press ESC to abort, ENTER to boot: Auto-boot in 1 seconds - press ESC to abort, ENTER to boot: Auto-boot in 0 seconds - press ESC to abort, ENTER to boot:
/-\|/-\|/-
Pegasos boot menu
1: MorphOS
2: Debian GNU/Linux 2.4 kernel
3: Debian GNU/Linux 2.6.4 kernel
4: Debian GNU/Linux 2.6.8 kernel
5: Gentoo 2.6.10
6: Gentoo 2.6.12
7: Polaris Test
8: return to OF prompt
press 1-8 within 30 seconds (default: 5) : press 1-8 within 29 seconds (default: 5) : press 1-8 within 29 seconds (default: 5) : press 1-8 within 29 seconds (default: 5) : press 1-8 within 29 seconds (default: 5) : press 1-8 within 29 seconds (default: 5) : press 1-8 within 29 seconds (default: 5) : press 1-8 within 29 seconds (default: 5) : press 1-8 within 29 seconds (default: 5) : press 1-8 within 29 seconds (default: 5) : press 1-8 within 29 seconds (default: 5) : press 1-8 within 28 seconds (default: 5) : press 1-8 within 28 seconds (default: 5) : press 1-8 within 28 seconds (default: 5) : press 1-8 within 28 seconds (default: 5) : press 1-8 within 28 seconds (default: 5) : press 1-8 within 28 seconds (default: 5) :
\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|
Starting Polaris: Opensolaris on PPC...
Sun Labs in collaboration with the Polaris community.
BSS cleared from 00b066d8 - 00b692b0 (Size 62bd8)
Found Valid CPU... Processor Version Reg = 80020101
mlsetup.c:120: mlsetup() starting...
Initialized t0 thread.
mlsetup.c:230: fiximp_obp() starting...
Obtained timebase frequency = 33333333 hz
Calculated timebase period = 0
Calculated timebase ticks pre 10usec = 333
mlsetup.c:276: fiximp_obp() done.
mlsetup.c:199: mlsetup() done.
Number test for 127 in o d x: 177 127 7f
Leaving locore.s ... executing main()...
startup.c:169: startup_init() starting...
startup.c:185: startup_init() done
startup.c:233: startup_memlist() starting...
mlsetup.c:475: bgetprop() starting...
=======
Let us know if you want to give it a try! We have a binary we can send you.
R&B