U-Boot 2009.01-1.2.19-lange51 (May 06 2010 - 11:52:45)

CPU: Freescale i.MX51 family 3.0V at 800 MHz
mx51 pll1: 800MHz
mx51 pll2: 665MHz
mx51 pll3: 216MHz
ipg clock : 66500000Hz
ipg per clock : 665000000Hz
uart clock : 66500000Hz
cspi clock : 54000000Hz
Board: MX51 LANGE51 3.0 [POR]
DRAM: 512 MB
JEDEC ID: 0xbf:0x25:0x4a
Reading SPI NOR flash 0x40000 [0x10000 bytes] -> ram 0x975f06e8
.SUCCESS

*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
board id: 1.0.1, rev1.3
Boot Source: SPI NOR FLASH BOOT
SD card.
Vendor: Man 02 OEM TM "SD02G" Date 03/2010
Product: 2863884823
Revision: 6.0
reading uImage
reading system.conf

** Unable to read "system.conf" from mmc 0:1 **
Boot Cmd: run sd_boot
Hit any key to stop autoboot: 1 0
## Error: "base_cmd99" not defined
SD card.
Vendor: Man 02 OEM TM "SD02G" Date 03/2010
Product: 2863884823
Revision: 6.0
reading uImage
## Booting kernel from Legacy Image at 90007fc0 ...
Image Name: Linux-2.6.31.14-efikamx
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2658376 Bytes = 2.5 MB
Load Address: 90008000
Entry Point: 90008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux................................................................................................................................................................. done, booting the kernel.
[ 0.000000] Linux version 2.6.31.14-efikamx (neko@excel) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #1 PREEMPT Tue Sep 14 22:23:30 CDT 2010
[ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Genesi Efika MX (Smarttop)
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 105664
[ 0.000000] Kernel command line: noinitrd console=ttymxc0,115200 console=tty1 root=/dev/mmcblk0p2 rw
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 416MB = 416MB total
[ 0.000000] Memory: 416700KB available (4556K code, 528K data, 140K init, 0K highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:368
[ 0.000000] MXC IRQ initialized
[ 0.000000] MXC_Early serial console at MMIO 0x73fbc000 (options '115200')
[ 0.000000] console [ttymxc0] enabled
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console handover: boot [ttymxc0] -> real [tty1]
[ 0.000000] Linux version 2.6.31.14-efikamx (neko@excel) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #1 PREEMPT Tue Sep 14 22:23:30 CDT 2010
[ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Genesi Efika MX (Smarttop)
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 105664
[ 0.000000] Kernel command line: noinitrd console=ttymxc0,115200 console=tty1 root=/dev/mmcblk0p2 rw
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 416MB = 416MB total
[ 0.000000] Memory: 416700KB available (4556K code, 528K data, 140K init, 0K highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:368
[ 0.000000] MXC IRQ initialized
[ 0.000000] MXC_Early serial console at MMIO 0x73fbc000 (options '115200')
[ 0.000000] console [ttymxc0] enabled
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console handover: boot [ttymxc0] -> real [tty1]
[ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] tmpfs: No value for mount option 'mode'
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] i.MX IRAM pool: 128 KB@0x9a840000
[ 0.000000] IRAM READY
[ 0.000000] CPU is i.MX51 Revision 3.0
[ 0.000000] MXC GPIO hardware
[ 0.000000] Efika MX: IOMUX for Board ID (3 pins)
[ 0.000000] Efika MX: IOMUX for General GPIO Stuff (7 pins)
[ 0.000000] Efika MX: IOMUX for SPI (6 pins)
[ 0.000000] Efika MX: IOMUX for PMIC (1 pins)
[ 0.000000] Efika MX: IOMUX for I2C (4 pins)
[ 0.000000] Efika MX: IOMUX for USB (29 pins)
[ 0.000000] Efika MX: IOMUX for ATA (29 pins)
[ 0.000000] Efika MX: Initializing SD card IOMUX (external, mmc0)
[ 0.000000] Efika MX: IOMUX for WDOG (1.2) (1 pins)
[ 0.000000] Efika MX: IOMUX for LED (3 pins)
[ 0.000000] Efika MX: IOMUX for Power Key (1 pins)
[ 0.000000] Efika MX: AIPS1_BASE_ADDR = 0x73f00000
[ 0.000000] Efika MX: AIPS1_BASE_ADDR_VIRT = 0xf7e00000, io_pg_offst = 0x3df8
[ 0.000000] Efika MX: PHYS_OFFSET = 0x90000000
[ 0.000000] Efika MX Revision 1.3
[ 0.000000] Using SDMA I.API
[ 0.000000] MXC DMA API initialized
[ 0.000000] bio: create slab <bio-0> at 0
[ 0.000000] SCSI subsystem initialized
[ 0.000000] CSPI: mxc_spi-0 probed
[ 0.000000] usbcore: registered new interface driver usbfs
[ 0.000000] usbcore: registered new interface driver hub
[ 0.000000] usbcore: registered new device driver usb
[ 0.000000] IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
[ 0.000000] mc13892 Rev 2.0 FinVer 2 detected
[ 0.000000] Initializing regulators for Efika MX
[ 0.000000] regulator: SW1: 600 <--> 1375 mV
[ 0.000000] regulator: SW2: 900 <--> 1850 mV
[ 0.000000] regulator: SW3: 1100 <--> 1850 mV
[ 0.000000] regulator: SW4: 1100 <--> 1850 mV
[ 0.000000] regulator: SWBST: 0 mV
[ 0.000000] regulator: VIOHI: 0 mV
[ 0.000000] regulator: VPLL: 1050 <--> 1800 mV
[ 0.000000] regulator: VDIG: 1650 mV
[ 0.000000] regulator: VSD: 1800 <--> 3150 mV
[ 0.000000] regulator: VUSB2: 2400 <--> 2775 mV
[ 0.000000] regulator: VVIDEO: 2775 mV
[ 0.000000] regulator: VAUDIO: 2300 <--> 3000 mV
[ 0.000000] regulator: VCAM: 2500 <--> 3000 mV fast normal
[ 0.000000] regulator: VGEN1: 1200 <--> 3150 mV
[ 0.000000] regulator: VGEN2: 1200 <--> 3150 mV
[ 0.000000] regulator: VGEN3: 1800 <--> 2900 mV
[ 0.000000] regulator: VUSB: 0 mV
[ 0.000000] regulator: GPO1: 0 mV
[ 0.000000] regulator: GPO2: 0 mV
[ 0.000000] regulator: GPO3: 0 mV
[ 0.000000] regulator: GPO4: 0 mV
[ 0.000000] Device spi1.0 probed
[ 0.000000] NET: Registered protocol family 2
[ 0.000000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.539123] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.539711] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.540014] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.540044] TCP reno registered
[ 0.540239] NET: Registered protocol family 1
[ 0.541094] LPMode driver module loaded
[ 0.541128] Static Power Management for Freescale i.MX51
[ 0.541408] PM driver module loaded
[ 0.541653] sdram autogating driver module loaded
[ 0.541955] Bus freq driver module loaded
[ 0.542011] mxc_dvfs_core_probe
[ 0.542274] DVFS driver module loaded
[ 0.542306] i.MXC CPU frequency driver
[ 0.542830] DVFS PER driver module loaded
[ 0.544497] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.544568] msgmni has been set to 814
[ 0.548598] alg: No test for stdrng (krng)
[ 0.548957] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.549002] io scheduler noop registered (default)
[ 0.549038] io scheduler cfq registered
[ 0.549531] *** sii9022_probe
[ 0.551820] SII9022 sink not found ! id=00
[ 0.568166] mxcfb_read_edid2
[ 0.568541] read_edid error!
[ 0.568741] *** mxc_init_fb vmode= video-mode=1 clock_auto=1
[ 0.568766] registering framebuffer for HDMI
[ 0.569821] mode_option=800x600-16@60
[ 0.570608] mxc_ipu mxc_ipu: Channel already disabled 9
[ 0.570620] mxc_ipu mxc_ipu: Channel already uninitialized 9
[ 0.570637] mxcfb_di_clock_adjust pixelclk=25000 rate=80000000
[ 0.570686] orig: parent=pll3 clk=216000000 this=ipu_di0_clk di_clk=27000000
[ 0.570811] adjust: parent=pll3 clk=80000000 this=ipu_di0_clk di_clk=40000000 ret=0 ret=0
[ 0.570922] skip sii9022_reinit!
[ 0.570951] mxc_ipu mxc_ipu: WARNING: adapt panel end blank lines
[ 0.738161] pclk 25000 same to previous one, skipping!
[ 0.738171] skip sii9022_reinit!
[ 0.738191] mxc_ipu mxc_ipu: WARNING: adapt panel end blank lines
[ 0.762616] Console: switching to colour frame buffer device 100x37
[ 0.908151] pclk 25000 same to previous one, skipping!
[ 0.908159] skip sii9022_reinit!
[ 0.908176] mxc_ipu mxc_ipu: WARNING: adapt panel end blank lines
[ 0.948127] registering framebuffer for VPU overlay
[ 0.950685] mxc_sdc_fb mxc_sdc_fb.2: Unable to allocate framebuffer memory
[ 0.952959] mxc_sdc_fb: probe of mxc_sdc_fb.2 failed with error -12
[ 0.955197] *** sii9022 lcd_probe
[ 0.957406] *** sii9022 lcd_init_fb
[ 0.978129] mxcfb_read_edid2
[ 0.980696] read_edid error!
[ 0.983054] mxcfb_update_default_var mode_opt=<NULL> vmode=
[ 0.985298] mxcfb_di_clock_adjust pixelclk=13468 rate=148500000
[ 0.987559] orig: parent=pll3 clk=80000000 this=ipu_di0_clk di_clk=40000000
[ 0.989949] adjust: parent=pll3 clk=148500000 this=ipu_di0_clk di_clk=74250000 ret=0 ret=0
[ 0.992306] sii9022_reinit 1280x720 13468
[ 1.132152] sii9022 1-0039: geometry 1280 720 1280 720 0
[ 1.134436] sii9022 1-0039: timings 13468 220 110 20 5 40 5
[ 1.136696] sii9022 1-0039: accel 0 sync 23 vmode=0
[ 1.138970] sii9022 1-0039: pclk 7425 refresh 6024 total x 1650 y 750
[ 1.141268] sii9022 1-0039: vmap idx=6 vcode=4
[ 1.143933] hdmi audio mute
[ 1.154350] hdmi audio unmute
[ 1.298153] pclk 13468 same to previous one, skipping!
[ 1.298164] sii9022_reinit 1280x720 13468 same to previous one, skipping
[ 1.318161] IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
[ 1.335186] sii9022 1-0039: turning on LCD
[ 1.624009] Serial: MXC Internal UART driver
[ 1.624347] mxcintuart.0: ttymxc0 at MMIO 0x73fbc000 (irq = 31) is a Freescale i.MX
[ 1.624560] console [ttymxc0] enabled
[ 2.779948] mxcintuart.1: ttymxc1 at MMIO 0x73fc0000 (irq = 32) is a Freescale i.MX
[ 2.792545] mxcintuart.2: ttymxc2 at MMIO 0x7000c000 (irq = 33) is a Freescale i.MX
[ 2.809166] loop: module loaded
[ 2.817295] pata_fsl pata_fsl: rchan=29 wchan=28
[ 2.825753] scsi0 : pata_fsl
[ 2.832818] ata1: PATA max UDMA/44 irq 70
[ 2.842565] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.958150] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 2.969145] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 3.008169] fsl-ehci fsl-ehci.0: irq 18, io base 0x73f80000
[ 3.021024] ata1.00: ATA-8: SanDisk pSSD-P2 8GB, SSD 5.20, max UDMA/133
[ 3.031313] ata1.00: 15649200 sectors, multi 0: LBA48
[ 3.040408] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 3.050534] usb usb1: configuration #1 chosen from 1 choice
[ 3.060518] hub 1-0:1.0: USB hub found
[ 3.067920] hub 1-0:1.0: 1 port detected
[ 3.154576] ata1.00: configured for UDMA/44
[ 3.178482] scsi 0:0:0:0: Direct-Access ATA SanDisk pSSD-P2 SSD PQ: 0 ANSI: 5
[ 3.191456] sd 0:0:0:0: [sda] 15649200 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 3.203015] sd 0:0:0:0: [sda] Write Protect is off
[ 3.211566] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.224986] sda:
[ 3.228062] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.241456] sda1 sda2
[ 3.249396] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.298145] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
[ 3.309040] usb 1-1: new high speed USB device using fsl-ehci and address 2
[ 3.320172] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
[ 3.358162] fsl-ehci fsl-ehci.1: irq 14, io base 0x73f80200
[ 3.468134] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
[ 3.478342] usb usb2: configuration #1 chosen from 1 choice
[ 3.488279] hub 2-0:1.0: USB hub found
[ 3.495960] hub 2-0:1.0: 1 port detected
[ 3.504361] usbcore: registered new interface driver libusual
[ 3.515432] mice: PS/2 mouse device common for all mice
[ 3.524892] MXC keypad loaded
[ 3.532472] mc13892 rtc probe start
[ 3.540675] usb 1-1: configuration #1 chosen from 1 choice
[ 3.551078] pmic_rtc pmic_rtc.1: rtc core: registered pmic_rtc as rtc0
[ 3.561554] mc13892 rtc probe succeed
[ 3.569404] i2c /dev entries driver
[ 3.578191] Linux video capture interface: v2.00
[ 3.588042] MXC Video Output MXC Video Output.0: Registered device video0
[ 3.598908] MXC WatchDog Driver 2.0
[ 3.606088] clk: Unable to get requested clock: wdog_clk
[ 3.615763] MXC Watchdog # 0 Timer: initial timeout 60 sec
[ 3.625337] cpuidle: using governor ladder
[ 3.633210] cpuidle: using governor menu
[ 3.641387] PMIC Character device: successfully loaded
[ 3.651177] VPU initialized
[ 3.657898] mxsdhci: MXC Secure Digital Host Controller Interface driver
[ 3.668397] mxsdhci: MXC SDHCI Controller Driver.
[ 3.677182] mmc0: SDHCI detect irq 128 irq 1 INTERNAL DMA
[ 3.686797] Registered led device: efikamx:green
[ 3.695309] Registered led device: efikamx:red
[ 3.713663] Registered led device: efikamx:blue
[ 3.726169] usbcore: registered new interface driver usbhid
[ 3.735411] usbhid: v2.6:USB HID core driver
[ 3.754698] Advanced Linux Sound Architecture Driver Version 1.0.20.
[ 3.813582] sgtl5000-i2c 1-000a: SGTL5000 revision 17
[ 3.828169] usb 2-1: new high speed USB device using fsl-ehci and address 2
[ 3.855272] No device for DAI imx-ssi-1-0
[ 3.863056] No device for DAI imx-ssi-1-1
[ 3.870657] No device for DAI imx-ssi-2-0
[ 3.878139] No device for DAI imx-ssi-2-1
[ 3.886574] DMA Sound Buffers Allocated:UseIram=1 buf->addr=1fff6000 buf->area=9a856000 size=24576
[ 3.899349] DMA Sound Buffers Allocated:UseIram=1 buf->addr=a8318000 buf->area=f9e30000 size=24576
[ 3.911668] asoc: SGTL5000 <-> imx-ssi-2-0 mapping ok
[ 3.966728] mmc0: new high speed SD card at address 0f99
[ 3.975751] mmcblk0: mmc0:0f99 SD02G 1.83 GiB
[ 3.983954] mmcblk0: p1 p2
[ 4.010463] usb 2-1: configuration #1 chosen from 1 choice
[ 4.020501] hub 2-1:1.0: USB hub found
[ 4.027860] hub 2-1:1.0: 4 ports detected
[ 4.036383] ALSA device list:
[ 4.042833] #0: imx-3stack (SGTL5000)
[ 4.050987] TCP cubic registered
[ 4.057379] NET: Registered protocol family 17
[ 4.065142] ThumbEE CPU extension supported.
[ 4.072626] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[ 4.085812] regulator_init_complete: incomplete constraints, leaving GPO4 on
[ 4.096557] regulator_init_complete: incomplete constraints, leaving GPO3 on
[ 4.107053] regulator_init_complete: incomplete constraints, leaving GPO2 on
[ 4.117401] regulator_init_complete: incomplete constraints, leaving GPO1 on
[ 4.127519] regulator_init_complete: incomplete constraints, leaving VGEN3 on
[ 4.137830] regulator_init_complete: incomplete constraints, leaving VGEN2 on
[ 4.148070] regulator_init_complete: incomplete constraints, leaving VGEN1 on
[ 4.158251] regulator_init_complete: incomplete constraints, leaving VCAM on
[ 4.168194] regulator_init_complete: incomplete constraints, leaving VAUDIO on
[ 4.178189] regulator_init_complete: incomplete constraints, leaving VSD on
[ 4.187943] regulator_init_complete: incomplete constraints, leaving SWBST on
[ 4.198345] pmic_rtc pmic_rtc.1: setting system clock to 1970-01-01 06:40:07 UTC (24007)
[ 4.211079] EXT3-fs: mmcblk0p2: couldn't mount because of unsupported optional features (240).
[ 4.223736] EXT2-fs: mmcblk0p2: couldn't mount because of unsupported optional features (240).
[ 4.257624] EXT4-fs (mmcblk0p2): barriers enabled
[ 4.266832] kjournald2 starting: pid 1027, dev mmcblk0p2:8, commit interval 5 seconds
[ 4.288019] EXT4-fs (mmcblk0p2): internal journal on mmcblk0p2:8
[ 4.297015] EXT4-fs (mmcblk0p2): delayed allocation enabled
[ 4.305515] EXT4-fs: file extents enabled
[ 4.313064] EXT4-fs: mballoc enabled
[ 4.319655] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode
[ 4.329597] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 4.340073] devtmpfs: mounted
[ 4.346359] Freeing init memory: 140K
[ 4.418460] usb 2-1.1: new high speed USB device using fsl-ehci and address 3
[ 4.557747] usb 2-1.1: configuration #1 chosen from 1 choice