Hello there,
maybe someone can help me with the error outputs from dmesg:
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Thanks
Stefan
Here's the complete dmesg:
Total memory = 1024MB; using 2048kB for hash table (at c0400000)
Linux version 2.6.8-powerpc (sven@pegasos2) (version gcc 3.3.5 (Debian 1:3.3.5-5)) #1 Sat Jan 8 22:01:09 CET 2005
PCI bus 0 controlled by pci at 80000000
PCI bus 0 controlled by pci at c0000000
Pegasos l2cr : L2 cache was not active, activating
On node 0 totalpages: 262144
DMA zone: 196608 pages, LIFO batch:16
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 65536 pages, LIFO batch:16
Built 1 zonelists
Kernel command line: root=/dev/hda1
PID hash table entries: 4096 (order 12: 32768 bytes)
time_init: decrementer frequency = 33.333333 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1028672k available (1732k kernel code, 1092k data, 164k init, 262144k highmem)
Calibrating delay loop... 665.60 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4690k freed
NET: Registered protocol family 16
PCI: Probing PCI hardware
radeonfb: Found Intel x86 BIOS ROM Image
radeonfb: No ATY,RefCLK property !
radeonfb: Retreived PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=250.00 Mhz, System=200.00 MHz
radeonfb: Monitor 1 type CRT found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
radeonfb: ATI Radeon Ya DDR SGRAM 128 MB
Thermal assist unit not available
audit: initializing netlink socket (disabled)
audit(1108896554.652:0): initialized
highmem bounce pool size: 64 pages
devfs: 2004-01-31 Richard Gooch (
rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Console: switching to colour frame buffer device 80x30
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pmac_zilog: 0.6 (Benjamin Herrenschmidt <
benh@kernel.crashing.org>)
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
input: Macintosh mouse button emulation
Warning: no ADB interface detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 164k init 60k pmac 32k prep
NET: Registered protocol family 1
VP_IDE: IDE controller at PCI slot 0000:00:0c.1
VP_IDE: chipset revision 6
VP_IDE: VIA vt8231 (rev 10) IDE UDMA100 controller on pci0000:00:0c.1
VP_IDE: 100% native mode on irq 14
ide0: BM-DMA at 0x1020-0x1027, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x1028-0x102f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: ST3120023A, ATA DISK drive
hdb: ST380012A, ATA DISK drive
Unhandled interrupt e, disabled
Using anticipatory io scheduler
ide0 at 0x1000-0x1007,0x100e on irq 14
hda: max request size: 128KiB
hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
hdb: max request size: 1024KiB
hdb: 156301488 sectors (80026 MB) w/1024KiB Cache, CHS=16383/255/63, UDMA(100)
/dev/ide/host0/bus0/target1/lun0: RDSK p1 p2 p3 p4 p5
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4082B, ATAPI CD/DVD-ROM drive
Unhandled interrupt f, disabled
ide1 at 0x1010-0x1017,0x101e on irq 15
[2342] init_ext3_fs(), err = 0
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding 524152k swap on /dev/hda2. Priority:-1 extents:1
Adding 500840k swap on /dev/hdb4. Priority:-2 extents:1
EXT3 FS on hda1, internal journal
serio: i8042 AUX port at 0x60,0x64 irq 12
atkbd.c: keyboard reset failed on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
atkbd.c: keyboard reset failed on isa0060/serio0
hdc: ATAPI 32X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ieee1394: Initialized config rom entry `ip1394'
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins <
bcollins@debian.org>
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ohci1394: $Rev: 1223 $ Ben Collins <
bcollins@debian.org>
PCI: Enabling device 0000:00:01.0 (0000 -> 0003)
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[9] MMIO=[80000000-800007ff] Max Packet=[2048]
MV-64340 10/100/1000 Ethernet Driver
MV-64340: Chip base remaped at 0xf21fe000
divert: allocating divert_blk for eth0
eth0: port 1 with MAC address 00:0b:2f:65:82:0e
RX TCP/UDP Checksum Offload ON,
TX and RX Interrupt Coalescing ON
RX NAPI Enabled
natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
originally by Donald Becker <
becker@scyld.com>
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
PCI: Enabling device 0000:00:05.0 (0000 -> 0003)
divert: allocating divert_blk for eth1
natsemi eth1: NatSemi DP8381[56] at 0xf2170000 (0000:00:05.0), 00:09:5b:61:2f:ba, IRQ 9, port TP.
via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
PCI: Enabling device 0000:00:0d.0 (0000 -> 0003)
divert: allocating divert_blk for eth2
eth2: VIA Rhine II at 0x80000800, 00:0b:2f:46:ba:48, IRQ 9.
eth2: MII PHY found at address 16, status 0x7849 advertising 01e1 Link 0000.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
PCI: Enabling device 0000:00:0c.2 (0000 -> 0001)
uhci_hcd 0000:00:0c.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:0c.2: irq 9, io base 00001040
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011060000004b2f]
uhci_hcd 0000:00:0c.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Enabling device 0000:00:0c.3 (0000 -> 0001)
uhci_hcd 0000:00:0c.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
ip1394: $Rev: 1224 $ Ben Collins <
bcollins@debian.org>
divert: not allocating divert_blk for non-ethernet device eth3
ip1394: eth3: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
uhci_hcd 0000:00:0c.3: irq 9, io base 00001060
uhci_hcd 0000:00:0c.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using address 2
usb 2-1: new full speed USB device using address 2
usbcore: registered new driver hiddev
input: USB HID v1.11 Keyboard [1241:1203] on usb-0000:00:0c.2-2
input: USB HID v1.11 Device [1241:1203] on usb-0000:00:0c.2-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usb 2-2: new low speed USB device using address 3
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Generic Model: USB Storage-SMC Rev: I03A
Type: Direct-Access ANSI SCSI revision: 02
Vendor: Generic Model: USB Storage-CFC Rev: I03A
Type: Direct-Access ANSI SCSI revision: 02
Vendor: Generic Model: USB Storage-MMC Rev: I03A
Type: Direct-Access ANSI SCSI revision: 02
Vendor: Generic Model: USB Storage-MSC Rev: I03A
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi removable disk sdb at scsi0, channel 0, id 0, lun 1
Attached scsi removable disk sdc at scsi0, channel 0, id 0, lun 2
Attached scsi removable disk sdd at scsi0, channel 0, id 0, lun 3
USB Mass Storage device found at 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
input: USB HID v1.10 Mouse [Logitech Trackball] on usb-0000:00:0c.3-2
ts: Compaq touchscreen protocol output
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
PCI: Enabling device 0000:00:06.0 (0000 -> 0002)
bttv0: Bt878 (rev 2) at 0000:00:06.0, irq: 9, latency: 0, mmio: 0x80002000
bttv0: detected: FlyVideo 98FM (LR50)/ Typhoon TView TV/FM Tuner [card=36], PCI subsystem ID is 1852:1852
bttv0: using: Lifeview FlyVideo 98FM LR50 / Typhoon TView TV/FM Tuner [card=36,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00f4ff00 [init]
bttv0: FlyVideo Radio=yes RemoteControl=yes Tuner=5 gpio=0xf4ff00
bttv0: FlyVideo LR90=no tda9821/tda9820=no capture_only=no
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) by bt878 #0 [sw]
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
PCI: Enabling device 0000:00:06.1 (0000 -> 0002)
cannot find the slot for index 0 (range 0-0)
ENS1371: probe of 0000:00:07.0 failed with error -12
PCI: Enabling device 0000:00:0c.5 (0000 -> 0001)
eth1: DSPCFG accepted after 0 usec.
eth1: link up.
eth1: Setting full-duplex based on negotiated link capability.
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c023a3e4(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
[drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies Inc RV280 [Radeon 9200]
[drm] Loading R200 Microcode
drivers/usb/input/hid-input.c: event field not found
drivers/usb/input/hid-input.c: event field not found
eth1: no IPv6 routers present
eth1: increased tx threshold, txcfg 0xd0f01004.
eth1: increased tx threshold, txcfg 0xd0f01006.
eth1: increased tx threshold, txcfg 0xd0f01008.
eth1: increased tx threshold, txcfg 0xd0f0100a.
eth1: increased tx threshold, txcfg 0xd0f0100c.
eth1: increased tx threshold, txcfg 0xd0f0100e.
eth1: increased tx threshold, txcfg 0xd0f01010.
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Aieee - PCI error! status 0xf0008008, PCI status 0x8280
Login
Register
FAQ
Search