Hi. I just upgraded U-Boot and kernel to the latest available. The HDMI display is now yellow and although a pattern for character and X modes is recognizable, they are very far from legible and the display goes black every few seconds.
Below is the dmesg output. It looks to me like the native resolution/timing for monitor is chosen ( 1920x1080 on Samsung SyncMaster XL2370 ). FWIW, the console would display correctly on same monitor prior to upgrade ( did not record dmesg output from prior kernel ).
Any suggestions appreciated.
Sven
___________________________________________
U-Boot 2009.01-1.1.7-efikamx (Dec 21 2009 - 14:00:56)
CPU: Freescale i.MX51 family 2.5V at 400 MHz
mx51 pll1: 800MHz
mx51 pll2: 665MHz
mx51 pll3: 216MHz
ipg clock : 66500000Hz
ipg per clock : 665000000Hz
uart clock : 66500000Hz
cspi clock : 54000000Hz
Board: Genesi Efika MX [POR]
DRAM: 512 MB
JEDEC ID: 0xbf:0x25:0x4a
Reading SPI NOR flash 0x40000 [0x10000 bytes] -> ram 0x975f06e8
.SUCCESS
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Boot Source: SPI NOR FLASH BOOT
board rev1.1
board rev1.1
No MMC card found
** Unable to use mmc 0:1 for fatls **
** Unable to use mmc 0:1 for fatload **
Type ID = 0
Boot Cmd: run pata_boot
Hit any key to stop autoboot: 0
EfikaMX > boot
Write reg = 15 value = 0x00400022
Reset IDE: Bus 0: OK
Device 0: Model: Flash Module Firm: Ver2.M1B Ser#: 38A3079B040000001760
Type: Hard Disk
Capacity: 3679.5 MB = 3.5 GB (7535808 x 512)
reading uImage
2366884 bytes read
## Booting kernel from Legacy Image at 90007fc0 ...
Image Name: Linux-2.6.31.9-ER1-efikamx
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2366820 Bytes = 2.3 MB
Load Address: 90008000
Entry Point: 90008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux..........................................................................................................................................
[ 0.000000] Linux version 2.6.31.9-ER1-efikamx (neko@eriol) (gcc version 4.4.1 (Sourcery G++ Lite 2009q3-67) ) #11 Thu Jan 7 18:58:55 CST 2010
[ 0.000000] CPU: ARMv7 Processor [412fc081] revision 1 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Efika MX
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line: noinitrd console=ttymxc0,115200 console=tty1 root=/dev/sda2 rw hdmi
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 480MB = 480MB total
[ 0.000000] Memory: 482572KB available (3980K code, 290K data, 108K init, 0K highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:272
[ 0.000000] MXC IRQ initialized
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty1] enabled
[ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[ 0.230000] Mount-cache hash table entries: 512
[ 0.230000] CPU: Testing write buffer coherency: ok
[ 0.230000] regulator: core version 0.5
[ 0.230000] NET: Registered protocol family 16
[ 0.230000] /proc/ioctl created
[ 0.230000] CPU is i.MX51 Revision 2.5
[ 0.230000] MXC GPIO hardware
[ 0.330000] IRAM READY
[ 0.330000] mxc_init_dvfs_per initialised
[ 0.330000] board ID: 1.1
[ 0.330000] Using SDMA I.API
[ 0.330000] MXC DMA API initialized
[ 0.340000] bio: create slab <bio-0> at 0
[ 0.340000] SCSI subsystem initialized
[ 0.340000] CSPI: mxc_spi-0 probed
[ 0.340000] usbcore: registered new interface driver usbfs
[ 0.340000] usbcore: registered new interface driver hub
[ 0.340000] usbcore: registered new device driver usb
[ 0.340000] MXC I2C driver
[ 0.340000] MXC I2C driver
[ 0.340000] MXC HS I2C driver
[ 0.350000] mc13892 Rev 2.0 FinVer 2 detected
[ 0.380000] Initializing regulators for Efika MX
[ 0.490000] regulator: SW1: 600 <--> 1375 mV
[ 0.520000] regulator: SW2: 900 <--> 1850 mV
[ 0.520000] regulator: SW3: 1100 <--> 1850 mV
[ 0.520000] regulator: SW4: 1100 <--> 1850 mV
[ 0.520000] regulator: SWBST: 0 mV
[ 0.540000] regulator: VIOHI: 0 mV
[ 0.560000] regulator: VPLL: 1050 <--> 1800 mV
[ 0.580000] regulator: VDIG: 1050 <--> 1800 mV
[ 0.580000] regulator: VSD: 1800 <--> 3150 mV
[ 0.600000] regulator: VUSB2: 2400 <--> 2775 mV
[ 0.640000] regulator: VVIDEO: 2775 mV
[ 0.640000] regulator: VAUDIO: 2300 <--> 3000 mV
[ 0.640000] regulator: VCAM: 2500 <--> 3000 mV fast normal
[ 0.640000] regulator: VGEN1: 1200 <--> 3150 mV
[ 0.640000] regulator: VGEN2: 1200 <--> 3150 mV
[ 0.640000] regulator: VGEN3: 1800 <--> 2900 mV
[ 0.660000] regulator: VUSB: 0 mV
[ 0.660000] regulator: GPO1: 0 mV
[ 0.660000] regulator: GPO2: 0 mV
[ 0.660000] regulator: GPO3: 0 mV
[ 0.660000] regulator: GPO4: 0 mV
[ 0.740000] Device spi1.0 probed
[ 0.740000] NET: Registered protocol family 2
[ 0.740000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.740000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.740000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.740000] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.740000] TCP reno registered
[ 0.740000] NET: Registered protocol family 1
[ 0.740000] LPMode driver module loaded
[ 0.740000] Static Power Management for Freescale i.MX51
[ 0.740000] PM driver module loaded
[ 0.740000] sdram autogating driver module loaded
[ 0.740000] Bus freq driver module loaded
[ 0.740000] usb: Host 1 host (isp1504) registered
[ 0.740000] usb: DR host (utmi) registered
[ 0.740000] mxc_dvfs_core_probe
[ 0.740000] DVFS driver module loaded
[ 0.740000] i.MXC CPU frequency driver
[ 0.740000] DVFS PER driver module loaded
[ 0.740000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.740000] msgmni has been set to 942
[ 0.750000] alg: No test for stdrng (krng)
[ 0.750000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.750000] io scheduler noop registered
[ 0.750000] io scheduler cfq registered (default)
[ 0.750000] *** sii9022_probe
[ 0.750000] *** monitor is detected
[ 0.750000] *** mxc_init_fb vmode= video-mode=4 clock_auto=1
[ 0.750000] mode_option=1280x720-24@60
[ 0.750000] mxc_ipu mxc_ipu: Channel already disabled 9
[ 0.750000] mxc_ipu mxc_ipu: Channel already uninitialized 9
[ 0.770000] Console: switching to colour frame buffer device 160x45
[ 0.790000] *** sii9022 lcd_probe
[ 0.790000] *** sii9022 lcd_init_fb
[ 0.790000] read_edid2
[ 0.820000] 00ffffffffffff004c2dc505333246452a130103801009782aee91a3544c9926
[ 0.820000] 0f5054230800a9408180814081009500b30001010101023a801871382d40582c
[ 0.820000] 4500a05a0000001e011d007251d01e206e285500a05a0000001e000000fd0032
[ 0.820000] 3c1b5111000a202020202020000000fc0053796e634d61737465720a202001c1
[ 0.820000] 02031cf14890041f0514130312230907078301000066030c00100080011d80d0
[ 0.820000] 721c1620102c2580a05a0000009e011d8018711c1620582c2500a05a0000009e
[ 0.820000] 011d00bc52d01e20b8285540a05a0000001e011d007251d01e206e285500a05a
[ 0.820000] 0000001e8c0ad090204031200c405500a05a0000001800000000000000000077
[ 0.820000] i2c-adapter i2c-1: ACK not received
[ 0.820000] ========================================
[ 0.830000] Display Information (EDID)
[ 0.830000] ========================================
[ 0.840000] EDID Version 1.3
[ 0.840000] Manufacturer: SAM
[ 0.850000] Model: 5c5
[ 0.850000] Serial#: 1162228275
[ 0.860000] Year: 2009 Week 42
[ 0.860000] Monitor Name: SyncMaster
[ 0.870000] Display Characteristics:
[ 0.870000] Monitor Operating Limits: From EDID
[ 0.880000] H: 27-81KHz V: 50-60Hz DCLK: 170MHz
[ 0.880000] Digital Display Input
[ 0.880000] Sync:
[ 0.890000] Max H-size in cm: 16
[ 0.900000] Max V-size in cm: 9
[ 0.900000] Gamma: 2.20
[ 0.910000] DPMS: Active yes, Suspend no, Standby no
[ 0.910000] RGB Color Display
[ 0.920000] Chroma
[ 0.920000] RedX: 0.640 RedY: 0.330
[ 0.930000] GreenX: 0.300 GreenY: 0.600
[ 0.930000] BlueX: 0.150 BlueY: 0.060
[ 0.930000] WhiteX: 0.313 WhiteY: 0.329
[ 0.940000] First DETAILED Timing is preferred
[ 0.940000] Detailed Timings
[ 0.950000] "1920x1080@60" 148 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync
[ 0.950000] "1280x720@60" 74 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
[ 0.960000] Supported VESA Modes
[ 0.960000] 640x480@60Hz
[ 0.970000] 800x600@56Hz
[ 0.970000] 800x600@60Hz
[ 0.980000] 1024x768@60Hz
[ 0.980000] Manufacturer's mask: 0
[ 0.980000] Standard Timings
[ 0.990000] 1600x1200@60Hz
[ 0.990000] 1280x1024@60Hz
[ 1.000000] 1280x960@60Hz
[ 1.000000] 1280x800@60Hz
[ 1.000000] 1440x900@60Hz
[ 1.010000] 1680x1050@60Hz
[ 1.010000] Detail Timings
[ 1.020000] ----------------------------------------
[ 1.020000] EIA/CEA-861 Information
[ 1.020000] Revision number: 3
[ 1.030000] DTV underscan: Supported
[ 1.030000] Basic audio: Supported
[ 1.030000] Detailed Timings
[ 1.040000] "1920x1080i@50" 74 1920 2448 2492 2640 1080 1084 1094 1124 +hsync +vsync
[ 1.040000] "1920x1080i@60" 74 1920 2008 2052 2200 1080 1084 1094 1124 +hsync +vsync
[ 1.040000] "1280x720@50" 74 1280 1720 1760 1980 720 725 730 750 +hsync +vsync
[ 1.050000] "1280x720@60" 74 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
[ 1.050000] "720x576@50" 27 720 732 796 864 576 581 586 625 -hsync -vsync
[ 1.050000] ========================================
[ 1.060000] Monitor/TV supported modelines
[ 1.060000] "1920x1080@60" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync
[ 1.070000] "1280x720@60" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
[ 1.070000] "640x480@60" 25.200 640 656 752 800 480 490 492 525 -hsync -vsync
[ 1.070000] "800x600@56" 36.01 800 824 896 1024 600 601 603 625 +hsync +vsync
[ 1.080000] "800x600@60" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
[ 1.080000] "1024x768@60" 65.02 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
[ 1.090000] "1600x1200@60" 162.22 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync
[ 1.090000] "1280x1024@60" 108.03 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
[ 1.100000] "1280x960@60" 108.03 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync
[ 1.100000] "1280x800@60" 83.647 1280 1347 1481 1683 800 801 804 828 -hsync -vsync
[ 1.100000] "1440x900@60" 106.780 1440 1523 1675 1910 900 901 904 932 -hsync -vsync
[ 1.110000] "1680x1050@60" 146.864 1680 1786 1966 2252 1050 1051 1054 1087 -hsync -vsync
[ 1.110000] "1920x1080i@50" 74.250 1920 2448 2492 2640 1080 1084 1094 1124 +hsync +vsync
[ 1.120000] "1920x1080i@60" 74.250 1920 2008 2052 2200 1080 1084 1094 1124 +hsync +vsync
[ 1.120000] "1280x720@50" 74.250 1280 1720 1760 1980 720 725 730 750 +hsync +vsync
[ 1.130000] "1280x720@60" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
[ 1.130000] "720x576@50" 27.00 720 732 796 864 576 581 586 625 -hsync -vsync
[ 1.140000] 1280x720@60 pclk=13468 removed (interlaced)
[ 1.140000] PREFERRED geometry 1920 1080 6734
[ 1.150000] PREFERRED timings 6734 148 88 36 4 44 5
[ 1.150000] PREFERRED flag 17 sync 3 vmode 0 preferred
[ 1.160000] 1680x1050@60 pclk=6809 removed (pixclk higher than 7518 limit)
[ 1.160000] 1600x1200@60 pclk=6172 removed (pixclk higher than 7518 limit)
[ 1.170000] 1920x1080@60 pclk=6734 removed (pixclk higher than 7518 limit)
[ 1.170000] uh-oh! deleted preferred mode!
[ 1.180000] mxcfb_update_default_var mode_opt=<NULL> vmode=
[ 1.180000] preferred mode geometry 1920 1080 6734
[ 1.190000] preferred mode timings 6734 148 88 36 4 44 5
[ 1.190000] preferred mode flag 17 sync 3 vmode 0 preferred
[ 1.200000] nearest mode (1920x1080@60 pclk=6734) is 1920x1080@60 pclk=13468
[ 1.200000] nearest mode geometry 1920 1080 13468
[ 1.210000] nearest mode timings 13468 148 88 30 4 44 10
[ 1.210000] nearest mode flag 1 sync 3 vmode 1
[ 1.220000] mxcfb_di_clock_adjust pixelclk=13468 rate=297000000
[ 1.220000] orig: parent=pll3 clk=216000000 this=ipu_di0_clk di_clk=27000000
[ 1.230000] adjust: parent=pll3 clk=297000000 this=ipu_di0_clk di_clk=74250000 ret=0 ret=0
[ 1.310000] reinit 1920x1080 13468
[ 1.320000] sii9022 1-0039: geometry 1920 1080 1920 1080 16
[ 1.320000] sii9022 1-0039: timings 13468 148 88 30 4 44 10
[ 1.320000] sii9022 1-0039: accel 0 sync 3 vmode=1
[ 1.320000] sii9022 1-0039: pclk 7425 refresh 3003 total x 2200 total y 1124
[ 1.320000] mxc_ipu mxc_ipu: IPU Error - IPU_INT_STAT_10 = 0x00080000
[ 1.320000] sii9022 1-0039: vmap idx=12 vcode=34
[ 1.320000] hdmi audio mute
[ 1.330000] hdmi audio unmute
[ 1.560000] Serial: MXC Internal UART driver
[ 1.560000] mxcintuart.0: ttymxc0 at MMIO 0x73fbc000 (irq = 31) is a Freescale i.MX
[ 1.560000] console [ttymxc0] enabled
[ 3.480000] mxcintuart.1: ttymxc1 at MMIO 0x73fc0000 (irq = 32) is a Freescale i.MX
[ 3.500000] mxcintuart.2: ttymxc2 at MMIO 0x7000c000 (irq = 33) is a Freescale i.MX
[ 3.520000] loop: module loaded
[ 3.520000] pata_fsl pata_fsl: rchan=29 wchan=28
[ 3.530000] scsi0 : pata_fsl
[ 3.540000] ata1: PATA max UDMA/44 irq 70
[ 3.560000] usbmon: debugfs is not available
[ 3.560000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.730000] ata1.00: CFA: Flash Module, Ver2.M1B, max UDMA/100
[ 3.740000] ata1.00: 7535808 sectors, multi 1: LBA
[ 3.770000] ata1.00: configured for UDMA/44
[ 3.780000] scsi 0:0:0:0: Direct-Access ATA Flash Module Ver2 PQ: 0 ANSI: 5
[ 3.790000] sd 0:0:0:0: [sda] 7535808 512-byte logical blocks: (3.85 GB/3.59 GiB)
[ 3.810000] sd 0:0:0:0: [sda] Write Protect is off
[ 3.820000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3.830000] sda:
[ 3.830000] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 3.850000] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 3.860000] sda1 sda2
[ 3.870000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.890000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.900000] fsl-ehci fsl-ehci.0: irq 14, io base 0x73f80200
[ 3.930000] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 3.940000] usb usb1: configuration #1 chosen from 1 choice
[ 3.950000] hub 1-0:1.0: USB hub found
[ 3.960000] hub 1-0:1.0: 1 port detected
[ 4.080000] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
[ 4.090000] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
[ 4.130000] fsl-ehci fsl-ehci.1: irq 18, io base 0x73f80000
[ 4.160000] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
[ 4.170000] usb usb2: configuration #1 chosen from 1 choice
[ 4.180000] hub 2-0:1.0: USB hub found
[ 4.190000] hub 2-0:1.0: 1 port detected
[ 4.200000] usbcore: registered new interface driver libusual
[ 4.210000] mice: PS/2 mouse device common for all mice
[ 4.220000] MXC keypad loaded
[ 4.230000] mc13892 rtc probe start
[ 4.260000] pmic_rtc pmic_rtc.1: rtc core: registered pmic_rtc as rtc0
[ 4.270000] mc13892 rtc probe succeed
[ 4.280000] i2c /dev entries driver
[ 4.290000] usb 1-1: new high speed USB device using fsl-ehci and address 2
[ 4.300000] MXC WatchDog Driver 2.0
[ 4.310000] clk: Unable to get requested clock: wdog_clk
[ 4.320000] MXC Watchdog # 0 Timer: initial timeout 60 sec
[ 4.330000] cpuidle: using governor ladder
[ 4.340000] cpuidle: using governor menu
[ 4.450000] usb 1-1: configuration #1 chosen from 1 choice
[ 4.460000] hub 1-1:1.0: USB hub found
[ 4.470000] hub 1-1:1.0: 4 ports detected
[ 4.600000] usb 2-1: new high speed USB device using fsl-ehci and address 2
[ 4.610000] VPU initialized
[ 4.620000] mxsdhci: MXC Secure Digital Host Controller Interface driver
[ 4.630000] mxsdhci: MXC SDHCI Controller Driver.
[ 4.640000] mmc0: SDHCI detect irq 128 irq 1 INTERNAL DMA
[ 4.650000] mxsdhci: MXC SDHCI Controller Driver.
[ 4.660000] mmc1: SDHCI detect irq 136 irq 2 INTERNAL DMA
[ 4.670000] Registered led device: efikamx:green:power
[ 4.780000] Registered led device: efikamx:red:ide
[ 4.790000] Registered led device: efikamx:blue:sdhc
[ 4.820000] usbcore: registered new interface driver usbhid
[ 4.830000] usbhid: v2.6:USB HID core driver
[ 4.940000] usb 2-1: configuration #1 chosen from 1 choice
[ 4.950000] Advanced Linux Sound Architecture Driver Version 1.0.20.
[ 7.160000] sgtl5000-i2c 1-000a: SGTL5000 revision 17
[ 7.190000] No device for DAI imx-ssi-1-0
[ 7.200000] No device for DAI imx-ssi-1-1
[ 7.210000] No device for DAI imx-ssi-2-0
[ 7.210000] No device for DAI imx-ssi-2-1
[ 7.220000] DMA Sound Buffers Allocated:UseIram=1 buf->addr=1fff3000 buf->area=de8a8000 size=24576
[ 7.240000] DMA Sound Buffers Allocated:UseIram=1 buf->addr=ac270000 buf->area=fbe6d000 size=24576
[ 7.250000] asoc: SGTL5000 <-> imx-ssi-2-0 mapping ok
[ 7.310000] ALSA device list:
[ 7.310000] #0: imx-3stack (SGTL5000)
[ 7.320000] TCP cubic registered
[ 7.330000] NET: Registered protocol family 17
[ 7.340000] ThumbEE CPU extension supported.
[ 7.350000] input: Genesi Efika MX Buttons as /devices/virtual/input/input0
[ 7.360000] usb 1-1.1: new high speed USB device using fsl-ehci and address 3
[ 7.380000] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[ 7.390000] regulator_init_complete: incomplete constraints, leaving GPO4 on
[ 7.400000] regulator_init_complete: incomplete constraints, leaving GPO3 on
[ 7.420000] regulator_init_complete: incomplete constraints, leaving GPO2 on
[ 7.430000] regulator_init_complete: incomplete constraints, leaving GPO1 on
[ 7.440000] regulator_init_complete: incomplete constraints, leaving VUSB on
[ 7.450000] regulator_init_complete: incomplete constraints, leaving VGEN3 on
[ 7.460000] regulator_init_complete: incomplete constraints, leaving VGEN2 on
[ 7.480000] regulator_init_complete: incomplete constraints, leaving VGEN1 on
[ 7.490000] regulator_init_complete: incomplete constraints, leaving VCAM on
[ 7.500000] regulator_init_complete: incomplete constraints, leaving VAUDIO on
[ 7.510000] regulator_init_complete: incomplete constraints, leaving VUSB2 on
[ 7.520000] regulator_init_complete: incomplete constraints, leaving VSD on
[ 7.530000] regulator_init_complete: incomplete constraints, leaving VPLL on
[ 7.540000] regulator_init_complete: incomplete constraints, leaving VIOHI on
[ 7.560000] regulator_init_complete: incomplete constraints, leaving SWBST on
[ 7.580000] pmic_rtc pmic_rtc.1: setting system clock to 2010-01-17 00:06:34 UTC (1263686794)
[ 7.590000] EXT3-fs: sda2: couldn't mount because of unsupported optional features (240).
[ 7.600000] EXT2-fs: sda2: couldn't mount because of unsupported optional features (240).
[ 7.620000] EXT4-fs (sda2): barriers enabled
[ 7.650000] kjournald2 starting: pid 1014, dev sda2:8, commit interval 5 seconds
[ 7.660000] EXT4-fs (sda2): warning: maximal mount count reached, running e2fsck is recommended
[ 7.680000] EXT4-fs (sda2): internal journal on sda2:8
[ 7.690000] EXT4-fs (sda2): delayed allocation enabled
[ 7.700000] EXT4-fs: file extents enabled
[ 7.710000] EXT4-fs: mballoc enabled
[ 7.720000] EXT4-fs (sda2): mounted filesystem with ordered data mode
[ 7.730000] VFS: Mounted root (ext4 filesystem) on device 8:2.
[ 7.740000] Freeing init memory: 108K
[ 7.760000] usb 1-1.1: configuration #1 chosen from 1 choice
[ 12.160000] Error: Driver 'rt2870' is already registered, aborting...
[ 12.170000] usbcore: error -16 registering interface driver rt2870
[ 13.760000] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
[ 14.080000] phy0 -> rt2x00lib_request_firmware: Error - Failed to request Firmware.
Ubuntu 9.10 efikamx ttymxc0
efikamx login:
|