Unanswered topics | Active topics


Board index » »

All times are UTC-06:00



Post new topic  Reply to topic  Page 1 of 1
  [ 12 posts ] 
  Previous topic | Next topic 
Author Message
frankm
PostPosted: Fri Nov 11, 2011 11:32 am 
Offline

Joined: Fri Nov 11, 2011 10:21 am
Posts: 21
Location: Netherlands
This week I received my Efika MX nettop, unfortunately all I get from it is a black screen, in addition to the installed version of Maverick I tried the october release, armhf+3d, Android and William Schaub's headless Maverick, http://steubentech.com/~talon/Efika-MX/ ... /maverick/. Upon booting any of these, the backlight of my display is turned on and then it goes to sleep, pressing the display's menu button, to prevent it from going to sleep, doesn't help, neither does plugging in the cable while the machine is booting. The headless Maverick did allow me to get a dmesg and the EDID file, by logging in remotely via ssh, I don't have the debug board, hopefully these two will help diagnose and solve the problem.

Frank.

My monitor is a NEC MultiSync EA191M, a 1280x1024 pva panel,
here is the parsed EDID file:
Code:
# EDID version 1 revision 3
Section "Monitor"
# Block type: 2:0 3:fd
# Block type: 2:0 3:fc
Identifier "EA191M"
VendorName "NEC"
ModelName "EA191M"
# Block type: 2:0 3:fd
HorizSync 31-81
VertRefresh 56-75
# Max dot clock (video bandwidth) 140 MHz
# Block type: 2:0 3:fc
# Block type: 2:0 3:ff
# DPMS capabilities: Active off:yes Suspend:yes Standby:yes

Mode "1280x1024" # vfreq 60.020Hz, hfreq 63.981kHz
DotClock 108.000000
HTimings 1280 1328 1440 1688
VTimings 1024 1025 1028 1066
Flags "+HSync" "+VSync"
EndMode
# Block type: 2:0 3:fd
# Block type: 2:0 3:fc
# Block type: 2:0 3:ff
EndSection
And dmesg:
Code:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.31.14.21-efikamx (steev@jones) (gcc version 4.5.2 (Ubuntu/Linaro 4.5.2-5ubuntu2~ppa1) ) #2 PREEMPT Tue Apr 12 17:07:36 CDT 2011
[ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Genesi Efika MX (Smarttop)
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 106496
[ 0.000000] free_area_init_node: node 0, pgdat 804199bc, node_mem_map 8047e000
[ 0.000000] DMA zone: 192 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 24384 pages, LIFO batch:3
[ 0.000000] Normal zone: 640 pages used for memmap
[ 0.000000] Normal zone: 81280 pages, LIFO batch:15
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 105664
[ 0.000000] Kernel command line: console=tty1 root=/dev/mmcblk0p2 rootwait rw
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 416MB = 416MB total
[ 0.000000] Memory: 411360KB available (3560K code, 589K data, 136K init, 0K highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:368
[ 0.000000] MXC IRQ initialized
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty1] enabled
[ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] Initializing cgroup subsys ns
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Initializing cgroup subsys freezer
[ 0.000000] Initializing cgroup subsys net_cls
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] i.MX IRAM pool: 128 KB@0x9a840000
[ 0.000000] IRAM READY
[ 0.000000] CPU is i.MX51 Revision 3.0
[ 0.000000] MXC GPIO hardware
[ 0.000000] Efika MX: mmc0 configured as external SDHC
[ 0.000000] Efika MX: Smarttop Revision 1.3
[ 0.000000] Using SDMA I.API
[ 0.000000] MXC DMA API initialized
[ 0.000000] bio: create slab <bio-0> at 0
[ 0.000000] SCSI subsystem initialized
[ 0.000000] CSPI: mxc_spi-0 probed
[ 0.000000] IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
[ 0.000000] NET: Registered protocol family 8
[ 0.000000] NET: Registered protocol family 20
[ 0.000000] mc13892 Rev 2.0 FinVer 2 detected
[ 0.000000] Initializing regulators for Efika MX
[ 0.000000] regulator: SW1: 600 <--> 1375 mV
[ 0.000000] regulator: SW2: 900 <--> 1850 mV
[ 0.000000] regulator: SW3: 1100 <--> 1850 mV
[ 0.000000] regulator: SW4: 1100 <--> 1850 mV
[ 0.000000] regulator: SWBST: 0 mV
[ 0.000000] regulator: VIOHI: 0 mV
[ 0.000000] regulator: VPLL: 1050 <--> 1800 mV
[ 0.000000] regulator: VDIG: 1650 mV
[ 0.000000] regulator: VSD: 1800 <--> 3150 mV
[ 0.000000] regulator: VUSB2: 2400 <--> 2775 mV
[ 0.000000] regulator: VVIDEO: 2775 mV
[ 0.000000] regulator: VAUDIO: 2300 <--> 3000 mV
[ 0.000000] regulator: VCAM: 2500 <--> 3000 mV fast normal
[ 0.000000] regulator: VGEN1: 1200 <--> 3150 mV
[ 0.000000] regulator: VGEN2: 1200 <--> 3150 mV
[ 0.000000] regulator: VGEN3: 1800 <--> 2900 mV
[ 0.000000] regulator: VUSB: 0 mV
[ 0.000000] regulator: GPO1: 0 mV
[ 0.000000] regulator: GPO2: 0 mV
[ 0.000000] regulator: GPO3: 0 mV
[ 0.000000] regulator: GPO4: 0 mV
[ 0.000000] Device spi1.0 probed
[ 1.111686] Switched to high resolution mode on CPU 0
[ 1.112728] NET: Registered protocol family 2
[ 1.113111] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.114154] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.114738] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 1.115038] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.115070] TCP reno registered
[ 1.115296] NET: Registered protocol family 1
[ 1.115531] Unpacking initramfs...
[ 1.530067] Freeing initrd memory: 6120K
[ 1.531035] LPMode driver module loaded
[ 1.531070] Static Power Management for Freescale i.MX51
[ 1.531415] PM driver module loaded
[ 1.531807] sdram autogating driver module loaded
[ 1.532228] Bus freq driver module loaded
[ 1.532294] mxc_dvfs_core_probe
[ 1.532627] DVFS driver module loaded
[ 1.532665] i.MXC CPU frequency driver
[ 1.533174] DVFS PER driver module loaded
[ 1.535073] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.535152] msgmni has been set to 815
[ 1.536835] alg: No test for stdrng (krng)
[ 1.537228] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.537278] io scheduler noop registered (default)
[ 1.537324] io scheduler cfq registered
[ 1.539584] mxc_ipu mxc_ipu: Channel already disabled 9
[ 1.539597] mxc_ipu mxc_ipu: Channel already uninitialized 9
[ 1.539637] mxc_sdc_fb mxc_sdc_fb.0: mxcfb: Error initializing panel.
[ 1.544452] Console: switching to colour frame buffer device 75x50
[ 2.192581] SIIHDMI: Device ID: 0xb0 (TPI revision 2.9)
[ 2.195613] SIIHDMI: sink detected (hotplug, receiver sense, )
[ 2.242457] SIIHDMI: Unsupported modelines:
[ 2.242571] SIIHDMI: v "1280x960@60" 108.03 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync
[ 2.242755] SIIHDMI: v "1152x864@75" 108.03 1152 1216 1344 1600 864 865 868 900 +hsync +vsync
[ 2.242937] SIIHDMI: p "1280x1024@75" 135.07 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync
[ 2.243126] SIIHDMI: v "1024x768@75" 78.802 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
[ 2.243308] SIIHDMI: v "832x624@75" 53.433 832 875 962 1092 624 625 628 652 -hsync -vsync
[ 2.243468] SIIHDMI: v "800x600@75" 49.500 800 816 896 1056 600 601 604 625 +hsync +vsync
[ 2.243626] SIIHDMI: v "800x600@60" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
[ 2.243783] SIIHDMI: v "800x600@56" 36.01 800 824 896 1024 600 601 603 625 +hsync +vsync
[ 2.250713] SIIHDMI: v "640x480@75" 31.500 640 656 720 840 480 481 484 500 -hsync -vsync
[ 2.257856] SIIHDMI: v "640x480@67" 27.106 640 661 725 810 480 481 484 499 -hsync -vsync
[ 2.265062] SIIHDMI: v "720x400@70" 26.171 720 737 808 896 400 401 404 417 -hsync -vsync
[ 2.272316] SIIHDMI: V "1280x1024@60" 108.03 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
[ 2.279599] SIIHDMI: Removed 12 modes due to incompatibilities
[ 2.283327] SIIHDMI: Supported modelines:
[ 2.287036] SIIHDMI: "1280x720@50" 74.250 1280 1720 1760 1980 720 725 730 750 +hsync +vsync
[ 2.294555] SIIHDMI: "1280x720@60" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
[ 2.302193] SIIHDMI: "720x576@50" 27.00 720 732 796 864 576 581 586 625 -hsync -vsync
[ 2.309930] SIIHDMI: "720x480@59" 27.00 720 736 798 858 480 489 495 525 -hsync -vsync
[ 2.317849] SIIHDMI: "1024x768@70" 75.01 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
[ 2.325977] SIIHDMI: "1024x768@60" 65.02 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
[ 2.334213] SIIHDMI: "800x600@72" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync
[ 2.342545] SIIHDMI: "640x480@72" 31.500 640 664 704 832 480 489 491 520 -hsync -vsync
[ 2.350888] SIIHDMI: "640x480@60" 25.200 640 656 752 800 480 490 492 525 -hsync -vsync
[ 2.359383] SIIHDMI: Setting Resolution: 1280x720@529
[ 2.505726] mxc_ipu mxc_ipu: Channel already disabled 9
[ 2.521713] IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
[ 2.568255] Serial: MXC Internal UART driver
[ 2.573476] mxcintuart.0: ttymxc0 at MMIO 0x73fbc000 (irq = 31) is a Freescale i.MX
[ 2.584412] loop: module loaded
[ 2.591171] mice: PS/2 mouse device common for all mice
[ 2.596261] mc13892 rtc probe start
[ 2.602312] pmic_rtc pmic_rtc.1: rtc core: registered pmic_rtc as rtc0
[ 2.607039] mc13892 rtc probe succeed
[ 2.611984] i2c /dev entries driver
[ 2.617327] Linux video capture interface: v2.00
[ 2.622531] mxc_v4l2_output mxc_v4l2_output.0: Registered device video0
[ 2.627427] MXC WatchDog Driver 2.0
[ 2.632203] clk: Unable to get requested clock: wdog_clk
[ 2.637148] MXC Watchdog # 0 Timer: initial timeout 60 sec
[ 2.641997] cpuidle: using governor ladder
[ 2.646474] cpuidle: using governor menu
[ 2.651366] PMIC Character device: successfully loaded
[ 2.656445] VPU initialized
[ 2.661716] Registered led device: efikamx:green
[ 2.666543] Registered led device: efikamx:red
[ 2.671240] Registered led device: efikamx:blue
[ 2.676698] Advanced Linux Sound Architecture Driver Version 1.0.20.
[ 2.686532] ALSA device list:
[ 2.690668] No soundcards found.
[ 2.696104] TCP cubic registered
[ 2.700132] NET: Registered protocol family 17
[ 2.704222] ThumbEE CPU extension supported.
[ 2.709330] input: Efika MX Input as /devices/virtual/input/input0
[ 2.714035] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[ 2.719486] regulator_init_complete: incomplete constraints, leaving GPO4 on
[ 2.723575] regulator_init_complete: incomplete constraints, leaving GPO3 on
[ 2.727488] regulator_init_complete: incomplete constraints, leaving GPO2 on
[ 2.731291] regulator_init_complete: incomplete constraints, leaving GPO1 on
[ 2.735058] regulator_init_complete: incomplete constraints, leaving VGEN1 on
[ 2.738663] regulator_init_complete: incomplete constraints, leaving VCAM on
[ 2.742217] regulator_init_complete: incomplete constraints, leaving VAUDIO on
[ 2.745751] regulator_init_complete: incomplete constraints, leaving VSD on
[ 2.749171] regulator_init_complete: incomplete constraints, leaving VDIG on
[ 2.752504] regulator_init_complete: incomplete constraints, leaving SWBST on
[ 2.771710] pmic_rtc pmic_rtc.1: setting system clock to 1970-01-01 18:16:05 UTC (65765)
[ 2.775065] Freeing init memory: 136K
[ 2.912091] udev[477]: starting version 163
[ 3.532909] usbcore: registered new interface driver usbfs
[ 3.536401] usbcore: registered new interface driver hub
[ 3.611930] usbcore: registered new device driver usb
[ 3.651037] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.761682] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 3.765031] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 3.791737] fsl-ehci fsl-ehci.0: irq 18, io base 0x73f80000
[ 3.813420] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 3.818574] usb usb1: configuration #1 chosen from 1 choice
[ 3.822320] hub 1-0:1.0: USB hub found
[ 3.825485] hub 1-0:1.0: 1 port detected
[ 3.994247] libata version 3.00 loaded.
[ 4.041702] usb 1-1: new high speed USB device using fsl-ehci and address 2
[ 4.051891] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
[ 4.052095] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
[ 4.081703] fsl-ehci fsl-ehci.1: irq 14, io base 0x73f80200
[ 4.181661] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
[ 4.182357] usb usb2: configuration #1 chosen from 1 choice
[ 4.182676] hub 2-0:1.0: USB hub found
[ 4.182846] hub 2-0:1.0: 1 port detected
[ 4.193261] pata_fsl pata_fsl: rchan=29 wchan=28
[ 4.193631] scsi0 : pata_fsl
[ 4.194617] ata1: PATA max UDMA/44 irq 70
[ 4.207147] usb 1-1: configuration #1 chosen from 1 choice
[ 4.374584] ata1.00: ATA-8: SanDisk pSSD-P2 8GB, SSD 5.20, max UDMA/133
[ 4.374772] ata1.00: 15649200 sectors, multi 0: LBA48
[ 4.417404] ata1.00: configured for UDMA/44
[ 4.417943] scsi 0:0:0:0: Direct-Access ATA SanDisk pSSD-P2 SSD PQ: 0 ANSI: 5
[ 4.420034] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.420881] sd 0:0:0:0: [sda] 15649200 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 4.421342] sd 0:0:0:0: [sda] Write Protect is off
[ 4.421467] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.421612] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.422674] sda: sda1 sda2
[ 4.440525] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.501776] usb 2-1: new high speed USB device using fsl-ehci and address 2
[ 4.552769] mxsdhci: MXC Secure Digital Host Controller Interface driver
[ 4.553925] mxsdhci: MXC SDHCI Controller Driver.
[ 4.559796] mmc0: SDHCI detect irq 128 irq 1 INTERNAL DMA
[ 4.652866] usb 2-1: configuration #1 chosen from 1 choice
[ 4.659023] hub 2-1:1.0: USB hub found
[ 4.659608] hub 2-1:1.0: 4 ports detected
[ 4.761478] mmc0: new high speed SDHC card at address a372
[ 4.766067] mmcblk0: mmc0:a372 SD04G 3.69 GiB
[ 4.766467] mmcblk0: p1 p2 p3
[ 4.941967] usb 2-1.1: new high speed USB device using fsl-ehci and address 3
[ 5.070376] usb 2-1.1: configuration #1 chosen from 1 choice
[ 5.152213] usb 2-1.2: new full speed USB device using fsl-ehci and address 4
[ 5.265390] usb 2-1.2: configuration #1 chosen from 1 choice
[ 5.271778] hub 2-1.2:1.0: USB hub found
[ 5.272573] hub 2-1.2:1.0: 3 ports detected
[ 5.314762] EXT4-fs (mmcblk0p2): barriers enabled
[ 5.316051] kjournald2 starting: pid 607, dev mmcblk0p2:8, commit interval 5 seconds
[ 5.320544] EXT4-fs (mmcblk0p2): internal journal on mmcblk0p2:8
[ 5.324744] EXT4-fs (mmcblk0p2): delayed allocation enabled
[ 5.328764] EXT4-fs: file extents enabled
[ 5.333628] EXT4-fs: mballoc enabled
[ 5.337597] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode
[ 5.552024] usb 2-1.2.1: new low speed USB device using fsl-ehci and address 5
[ 5.767915] usb 2-1.2.1: configuration #1 chosen from 1 choice
[ 5.852023] usb 2-1.2.3: new full speed USB device using fsl-ehci and address 6
[ 5.969416] usb 2-1.2.3: configuration #1 chosen from 1 choice
[ 9.882120] udev[666]: starting version 163
[ 10.492558] sgtl5000-i2c 1-000a: SGTL5000 revision 17
[ 10.599490] rt2870sta: module is from the staging directory, the quality is unknown, you have been warned.
[ 10.865726] rtusb init --->
[ 10.971308] usbcore: registered new interface driver rt2870
[ 11.100516] input: Mitsumi Electric Apple Extended USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2.3/2-1.2.3:1.0/input/input1
[ 11.101759] generic-usb 0003:05AC:020C.0002: input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-fsl-ehci.1-1.2.3/input0
[ 11.234278] input: Mitsumi Electric Apple Extended USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2.3/2-1.2.3:1.1/input/input2
[ 11.235194] generic-usb 0003:05AC:020C.0003: input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-fsl-ehci.1-1.2.3/input1
[ 11.235458] usbcore: registered new interface driver usbhid
[ 11.235478] usbhid: v2.6:USB HID core driver
[ 11.497042] eth0: register 'asix' at usb-fsl-ehci.0-1, ASIX AX88772 USB 2.0 Ethernet, 70:71:bc:9b:98:97
[ 11.497252] usbcore: registered new interface driver asix
[ 12.094594] input: Mitsumi Electric Apple Optical USB Mouse as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2.1/2-1.2.1:1.0/input/input3
[ 12.095498] apple 0003:05AC:0304.0001: input: USB HID v1.10 Mouse [Mitsumi Electric Apple Optical USB Mouse] on usb-fsl-ehci.1-1.2.1/input0
[ 13.175211] kjournald starting. Commit interval 15 seconds
[ 13.181176] EXT3 FS on mmcblk0p1, internal journal
[ 13.181204] EXT3-fs: mounted filesystem with writeback data mode.
[ 14.053574] NET: Registered protocol family 10
[ 14.063486] lo: Disabled Privacy Extensions
[ 14.711957] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 14.936094] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 19.635964] No device for DAI imx-ssi-1-0
[ 19.635989] No device for DAI imx-ssi-1-1
[ 19.636046] No device for DAI imx-ssi-2-0
[ 19.636059] No device for DAI imx-ssi-2-1
[ 19.667879] DMA Sound Buffers Allocated:UseIram=1 buf->addr=1ffe2000 buf->area=9a842000 size=24576
[ 19.668034] DMA Sound Buffers Allocated:UseIram=1 buf->addr=a8688000 buf->area=fa0cc000 size=24576
[ 19.668049] asoc: SGTL5000 <-> imx-ssi-2-0 mapping ok
[ 19.755425] MXC spdif support initialized
[ 24.771651] eth0: no IPv6 routers present
Top
   
Reply with quote  
frankm
PostPosted: Tue Nov 15, 2011 11:50 am 
Offline

Joined: Fri Nov 11, 2011 10:21 am
Posts: 21
Location: Netherlands
Today I gave Gentoo (gentoo-stage3-armv7a-20101216) a try and it appears to get a little further than the headless Maverick, it does support a 1280x1024 modeline, SIIHDMI even puts an asterix at the start of it, I have no idea what that means though, then it selects a 1280x720 modeline and I am left with a black screen.
How do I make it choose the 1280x1024 modeline and will that make any difference?

For what it's worth here is the dmesg of gentoo-stage3-armv7a-20101216
Code:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.31.14.25-efikamx (root@samwise.lan) (gcc version 4.6.1 (Debian 4.6.1-11) ) #1 Wed Sep 21 22:16:42 EEST 2011
[ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Genesi Efika MX (Smarttop)
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 118784
[ 0.000000] free_area_init_node: node 0, pgdat 8040bbac, node_mem_map 80472000
[ 0.000000] DMA zone: 192 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 24384 pages, LIFO batch:3
[ 0.000000] Normal zone: 736 pages used for memmap
[ 0.000000] Normal zone: 93472 pages, LIFO batch:31
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 117856
[ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw video=imx-ipuv3-fb:1024x600M-16@60 rootfstype=ext4 lpj=3997696
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 464MB = 464MB total
[ 0.000000] Memory: 462220KB available (3496K code, 596K data, 140K init, 0K highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:368
[ 0.000000] MXC IRQ initialized
[ 0.000000] MXC_Early serial console at MMIO 0x73fbc000 (options '115200')
[ 0.000000] console [ttymxc0] enabled
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop (skipped) preset value.. 799.53 BogoMIPS (lpj=3997696)
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] Initializing cgroup subsys ns
[ 0.000000] Initializing cgroup subsys freezer
[ 0.000000] Initializing cgroup subsys net_cls
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] i.MX IRAM pool: 128 KB@0x9d840000
[ 0.000000] IRAM READY
[ 0.000000] CPU is i.MX51 Revision 3.0
[ 0.000000] MXC GPIO hardware
[ 0.000000] Efika MX: mmc0 configured as external SDHC
[ 0.000000] Efika MX: Smarttop Revision 1.3
[ 0.000000] Using SDMA I.API
[ 0.000000] MXC DMA API initialized
[ 0.000000] bio: create slab <bio-0> at 0
[ 0.000000] SCSI subsystem initialized
[ 0.000000] libata version 3.00 loaded.
[ 0.000000] CSPI: mxc_spi-0 probed
[ 0.000000] IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
[ 0.000000] NET: Registered protocol family 8
[ 0.000000] NET: Registered protocol family 20
[ 0.000000] mc13892 Rev 2.0 FinVer 2 detected
[ 0.000000] Initializing regulators for Efika MX
[ 0.000000] regulator: SW1: 600 <--> 1375 mV
[ 0.000000] regulator: SW2: 900 <--> 1850 mV
[ 0.000000] regulator: SW3: 1100 <--> 1850 mV
[ 0.000000] regulator: SW4: 1100 <--> 1850 mV
[ 0.000000] regulator: SWBST: 0 mV
[ 0.000000] regulator: VIOHI: 0 mV
[ 0.000000] regulator: VPLL: 1050 <--> 1800 mV
[ 0.000000] regulator: VDIG: 1650 mV
[ 0.000000] regulator: VSD: 1800 <--> 3150 mV
[ 0.000000] regulator: VUSB2: 2400 <--> 2775 mV
[ 0.000000] regulator: VVIDEO: 2775 mV
[ 0.000000] regulator: VAUDIO: 2300 <--> 3000 mV
[ 0.000000] regulator: VCAM: 2500 <--> 3000 mV fast normal
[ 0.000000] regulator: VGEN1: 1200 <--> 3150 mV
[ 0.000000] regulator: VGEN2: 1200 <--> 3150 mV
[ 0.000000] regulator: VGEN3: 1800 <--> 2900 mV
[ 0.000000] regulator: VUSB: 0 mV
[ 0.000000] regulator: GPO1: 0 mV
[ 0.000000] regulator: GPO2: 0 mV
[ 0.000000] regulator: GPO3: 0 mV
[ 0.000000] regulator: GPO4: 0 mV
[ 0.000000] Device spi1.0 probed
[ 0.000000] NET: Registered protocol family 2
[ 1.166525] Switched to high resolution mode on CPU 0
[ 1.166944] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.174797] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.182617] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 1.189440] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.195979] TCP reno registered
[ 1.199324] NET: Registered protocol family 1
[ 1.203869] Unpacking initramfs...
[ 1.474569] Freeing initrd memory: 3692K
[ 1.479279] LPMode driver module loaded
[ 1.483125] Static Power Management for Freescale i.MX51
[ 1.488866] PM driver module loaded
[ 1.492579] sdram autogating driver module loaded
[ 1.497975] Bus freq driver module loaded
[ 1.502035] mxc_dvfs_core_probe
[ 1.505460] DVFS driver module loaded
[ 1.509174] i.MXC CPU frequency driver
[ 1.513333] DVFS PER driver module loaded
[ 1.518910] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.524782] msgmni has been set to 910
[ 1.529899] alg: No test for stdrng (krng)
[ 1.534285] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.541782] io scheduler noop registered (default)
[ 1.546617] io scheduler cfq registered
[ 1.552074] mxc_ipu mxc_ipu: Channel already disabled 9
[ 1.552086] mxc_ipu mxc_ipu: Channel already uninitialized 9
[ 1.569833] Console: switching to colour frame buffer device 80x30
[ 2.217393] SIIHDMI: Device ID: 0xb0 (TPI revision 2.9)
[ 2.225458] SIIHDMI: hotplug: display attached, powered on
[ 2.272151] SIIHDMI: Unsupported modelines:
[ 2.276355] SIIHDMI: "1280x1024@75" 135.07 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (pixel clock exceeded)
[ 2.287568] SIIHDMI: discarded 1 incompatible modes
[ 2.292453] SIIHDMI: supported modelines:
[ 2.296477] SIIHDMI: "1280x720@50" 74.250 1280 1720 1760 1980 720 725 730 750 +hsync +vsync
[ 2.305220] SIIHDMI: "1280x720@60" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
[ 2.313963] SIIHDMI: "720x576@50" 27.00 720 732 796 864 576 581 586 625 -hsync -vsync
[ 2.322183] SIIHDMI: "720x480@59" 27.00 720 736 798 858 480 489 495 525 -hsync -vsync
[ 2.330403] SIIHDMI: "1280x960@60" 108.03 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync
[ 2.339233] SIIHDMI: "1152x864@75" 108.03 1152 1216 1344 1600 864 865 868 900 +hsync +vsync
[ 2.347977] SIIHDMI: "1024x768@75" 78.802 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
[ 2.356720] SIIHDMI: "1024x768@70" 75.01 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
[ 2.365364] SIIHDMI: "1024x768@60" 65.02 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
[ 2.374019] SIIHDMI: "832x624@75" 53.433 832 875 962 1092 624 625 628 652 -hsync -vsync
[ 2.382412] SIIHDMI: "800x600@75" 49.500 800 816 896 1056 600 601 604 625 +hsync +vsync
[ 2.390805] SIIHDMI: "800x600@72" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync
[ 2.399112] SIIHDMI: "800x600@60" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
[ 2.407419] SIIHDMI: "800x600@56" 36.01 800 824 896 1024 600 601 603 625 +hsync +vsync
[ 2.415714] SIIHDMI: "640x480@75" 31.500 640 656 720 840 480 481 484 500 -hsync -vsync
[ 2.424021] SIIHDMI: "640x480@72" 31.500 640 664 704 832 480 489 491 520 -hsync -vsync
[ 2.432328] SIIHDMI: "640x480@67" 27.106 640 661 725 810 480 481 484 499 -hsync -vsync
[ 2.440634] SIIHDMI: "640x480@60" 25.200 640 656 752 800 480 490 492 525 -hsync -vsync
[ 2.448940] SIIHDMI: "720x400@70" 26.171 720 737 808 896 400 401 404 417 -hsync -vsync
[ 2.457247] SIIHDMI: * "1280x1024@60" 108.03 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
[ 2.466408] SIIHDMI: selected configuration:
[ 2.470792] SIIHDMI: "1280x720@60" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
[ 2.646545] IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
[ 2.688074] Serial: MXC Internal UART driver
[ 2.692527] mxcintuart.0: ttymxc0 at MMIO 0x73fbc000 (irq = 31) is a Freescale i.MX
[ 2.700282] console handover: boot [ttymxc0] -> real [ttymxc0]
[ 2.710595] loop: module loaded
[ 2.714891] pata_fsl pata_fsl: rchan=29 wchan=28
[ 2.719712] scsi0 : pata_fsl
[ 2.723089] ata1: PATA max UDMA/44 irq 70
[ 2.728652] mice: PS/2 mouse device common for all mice
[ 2.733960] mc13892 rtc probe start
[ 2.756875] pmic_rtc pmic_rtc.1: rtc core: registered pmic_rtc as rtc0
[ 2.763409] mc13892 rtc probe succeed
[ 2.767261] i2c /dev entries driver
[ 2.771304] Linux video capture interface: v2.00
[ 2.776419] mxc_v4l2_output mxc_v4l2_output.0: Registered device video0
[ 2.783273] MXC WatchDog Driver 2.0
[ 2.786928] clk: Unable to get requested clock: wdog_clk
[ 2.792504] MXC Watchdog # 0 Timer: initial timeout 60 sec
[ 2.798263] cpuidle: using governor ladder
[ 2.802366] cpuidle: using governor menu
[ 2.806739] PMIC Character device: successfully loaded
[ 2.812416] VPU initialized
[ 2.815550] mxsdhci: MXC Secure Digital Host Controller Interface driver
[ 2.822353] mxsdhci: MXC SDHCI Controller Driver.
[ 2.827601] mmc0: SDHCI detect irq 128 irq 1 INTERNAL DMA
[ 2.833670] Registered led device: efikamx:green
[ 2.838742] Registered led device: efikamx:red
[ 2.843537] Registered led device: efikamx:blue
[ 2.859320] Advanced Linux Sound Architecture Driver Version 1.0.20.
[ 2.873062] ALSA device list:
[ 2.876041] No soundcards found.
[ 2.880621] TCP cubic registered
[ 2.883859] NET: Registered protocol family 17
[ 2.888404] ThumbEE CPU extension supported.
[ 2.917691] input: Efika MX Input as /devices/virtual/input/input0
[ 2.924202] ata1.00: ATA-8: SanDisk pSSD-P2 8GB, SSD 5.20, max UDMA/133
[ 2.930899] ata1.00: 15649200 sectors, multi 0: LBA48
[ 2.936728] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[ 2.979454] regulator_init_complete: incomplete constraints, leaving GPO4 on
[ 2.986566] regulator_init_complete: incomplete constraints, leaving GPO3 on
[ 2.993621] regulator_init_complete: incomplete constraints, leaving GPO2 on
[ 3.000688] regulator_init_complete: incomplete constraints, leaving GPO1 on
[ 3.007756] regulator_init_complete: incomplete constraints, leaving VGEN1 on
[ 3.014897] regulator_init_complete: incomplete constraints, leaving VCAM on
[ 3.021962] regulator_init_complete: incomplete constraints, leaving VAUDIO on
[ 3.029202] regulator_init_complete: incomplete constraints, leaving VSD on
[ 3.036169] regulator_init_complete: incomplete constraints, leaving VDIG on
[ 3.043235] regulator_init_complete: incomplete constraints, leaving SWBST on
[ 3.054585] pmic_rtc pmic_rtc.1: setting system clock to 1970-01-05 22:27:47 UTC (426467)
[ 3.063121] ata1.00: configured for UDMA/44
[ 3.067719] scsi 0:0:0:0: Direct-Access ATA SanDisk pSSD-P2 SSD PQ: 0 ANSI: 5
[ 3.077096] sd 0:0:0:0: [sda] 15649200 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 3.085166] sd 0:0:0:0: [sda] Write Protect is off
[ 3.090026] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.090157] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.100019] sda:
[ 3.102192] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.108116] sda1 sda2
[ 3.122350] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.127063] Freeing init memory: 140K
[ 3.130728] BFS CPU scheduler v0.376 by Con Kolivas.
[ 3.186794] mmc0: new high speed SDHC card at address a372
[ 3.193201] mmcblk0: mmc0:a372 SD04G 3.69 GiB
[ 3.197906] mmcblk0: p1 p2
[ 3.252178] <30>udevd[516]: starting version 172
[ 3.374939] usbcore: registered new interface driver usbfs
[ 3.380615] usbcore: registered new interface driver hub
[ 3.386116] usbcore: registered new device driver usb
[ 3.423280] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.536665] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 3.543351] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 3.576640] fsl-ehci fsl-ehci.0: irq 18, io base 0x73f80000
[ 3.596617] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 3.602774] usb usb1: configuration #1 chosen from 1 choice
[ 3.608564] hub 1-0:1.0: USB hub found
[ 3.612387] hub 1-0:1.0: 1 port detected
[ 3.826672] usb 1-1: new high speed USB device using fsl-ehci and address 2
[ 3.836808] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
[ 3.843589] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
[ 3.876651] fsl-ehci fsl-ehci.1: irq 14, io base 0x73f80200
[ 3.966607] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
[ 3.972802] usb usb2: configuration #1 chosen from 1 choice
[ 3.978625] hub 2-0:1.0: USB hub found
[ 3.982446] hub 2-0:1.0: 1 port detected
[ 4.024785] usb 1-1: configuration #1 chosen from 1 choice
[ 4.297041] usb 2-1: new high speed USB device using fsl-ehci and address 2
[ 4.447559] usb 2-1: configuration #1 chosen from 1 choice
[ 4.461373] hub 2-1:1.0: USB hub found
[ 4.466848] hub 2-1:1.0: 4 ports detected
[ 4.650870] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 4.785277] usb 2-1.1: new high speed USB device using fsl-ehci and address 3
[ 4.898583] EXT4-fs (mmcblk0p2): barriers enabled
[ 4.905668] kjournald2 starting: pid 610, dev mmcblk0p2:8, commit interval 5 seconds
[ 4.915267] EXT4-fs (mmcblk0p2): internal journal on mmcblk0p2:8
[ 4.921422] EXT4-fs (mmcblk0p2): delayed allocation enabled
[ 4.927061] EXT4-fs: file extents enabled
[ 4.931457] EXT4-fs: mballoc enabled
[ 4.935103] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode
[ 4.986676] usb 2-1.1: configuration #1 chosen from 1 choice
[ 5.076722] usb 2-1.2: new full speed USB device using fsl-ehci and address 4
[ 5.200228] usb 2-1.2: configuration #1 chosen from 1 choice
[ 5.206314] hub 2-1.2:1.0: USB hub found
[ 5.210774] hub 2-1.2:1.0: 3 ports detected
[ 5.486986] usb 2-1.2.3: new full speed USB device using fsl-ehci and address 5
[ 5.604325] usb 2-1.2.3: configuration #1 chosen from 1 choice
[ 5.846999] usb 2-1.2.1: new low speed USB device using fsl-ehci and address 6
[ 6.062738] usb 2-1.2.1: configuration #1 chosen from 1 choice
[ 8.511506] <30>udevd[668]: starting version 172
[ 10.487236] sgtl5000-i2c 1-000a: SGTL5000 revision 17
[ 11.087807] input: Mitsumi Electric Apple Extended USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2.3/2-1.2.3:1.0/input/input1
[ 11.101082] generic-usb 0003:05AC:020C.0001: input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-fsl-ehci.1-1.2.3/input0
[ 11.157279] input: Mitsumi Electric Apple Extended USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2.3/2-1.2.3:1.1/input/input2
[ 11.170722] generic-usb 0003:05AC:020C.0002: input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-fsl-ehci.1-1.2.3/input1
[ 11.184501] usbcore: registered new interface driver usbhid
[ 11.190106] usbhid: v2.6:USB HID core driver
[ 11.350720] m25p80 spi1.1: sst25vf032b (4096 Kbytes)
[ 11.355696] Creating 3 MTD partitions on "spi_nor_flash":
[ 11.361154] 0x000000000000-0x000000040000 : "u-boot"
[ 11.366573] 0x000000040000-0x000000050000 : "config"
[ 11.371783] 0x000000050000-0x000000400000 : "spare"
[ 11.557354] input: Mitsumi Electric Apple Optical USB Mouse as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2.1/2-1.2.1:1.0/input/input3
[ 11.570544] apple 0003:05AC:0304.0003: input: USB HID v1.10 Mouse [Mitsumi Electric Apple Optical USB Mouse] on usb-fsl-ehci.1-1.2.1/input0
[ 11.984086] rt2870sta: module is from the staging directory, the quality is unknown, you have been warned.
[ 12.009891] rtusb init --->
[ 12.014869] usbcore: registered new interface driver rt2870
[ 13.203365] eth0: register 'asix' at usb-fsl-ehci.0-1, ASIX AX88772 USB 2.0 Ethernet, 70:71:bc:9b:98:97
[ 13.212954] usbcore: registered new interface driver asix
[ 13.491658] <30>udevd[687]: renamed network interface eth0 to eth10
[ 15.793355] kgsl_hal_init: hal->z430_regspace.mmio_phys_base = 0x30000000
[ 15.800278] kgsl_hal_init: hal->z430_regspace.mmio_virt_base = 0x9dc00000
[ 15.807087] kgsl_hal_init: hal->z430_regspace.sizebytes = 0x00020000
[ 15.813899] kgsl_hal_init: hal->z160_regspace.mmio_phys_base = 0xd0000000
[ 15.820705] kgsl_hal_init: hal->z160_regspace.mmio_virt_base = 0x9dbc8000
[ 15.827509] kgsl_hal_init: hal->z160_regspace.sizebytes = 0x00001000
[ 15.834301] GPU MMU enabled
[ 15.914238] Reserved memory: pa = 0xae000000 va = 0xa0000000 size = 0x02000000
[ 15.921483] GSL_HAL_MEM2 aperture (PHYS) pa = 0xae000000 va = 0xa0000000 size = 0x02000000
[ 15.929768] GSL_HAL_MEM1 aperture (MMU) pa = 0x00100000 va = 0x00100000 size = 0x08000000
[ 16.020368] No device for DAI imx-ssi-2-0
[ 16.024394] No device for DAI imx-ssi-2-1
[ 16.100796] DMA Sound Buffers Allocated:UseIram=1 buf->addr=1ffe2000 buf->area=9d842000 size=24576
[ 16.109931] DMA Sound Buffers Allocated:UseIram=1 buf->addr=a8388000 buf->area=f9e0b000 size=24576
[ 16.118914] asoc: SGTL5000 <-> imx-ssi-2-0 mapping ok
[ 18.285880] fuse init (API version 7.12)
Top
   
Reply with quote  
Neko
PostPosted: Tue Nov 15, 2011 12:26 pm 
Offline
Site Admin

Joined: Fri Sep 24, 2004 1:39 am
Posts: 1589
Location: Austin, TX
Quote:
Today I gave Gentoo (gentoo-stage3-armv7a-20101216) a try and it appears to get a little further than the headless Maverick, it does support a 1280x1024 modeline, SIIHDMI even puts an asterix at the start of it, I have no idea what that means though, then it selects a 1280x720 modeline and I am left with a black screen.
How do I make it choose the 1280x1024 modeline and will that make any difference?
It might, the easiest way is to add "siihdmi.seventwenty=0 siihdmi.teneighty=0" to your boot.script which will try and use a more traditional mode selection (i.e. closest to prefered) rather than trying to keep it close to 720p.

The asterisk means that it is the display's preferred mode, by the way (native panel resolution). The only reason we don't pick that mode by default is because somewhere above 1366x768 (including 1280x1024) the IPU driver can lock under heavy bandwidth, when doing multimedia etc.

I would really recommend using the latest kernel though. That's Gentoo and you're already using a version past the releases we did for Maverick, so you are obviously capable of compiling it yourself - go to github.com/genesi/linux-legacy and grab that and see what you get out of it. The development version is a little less flakey with displays but not totally working (or we'd have released it already).

_________________
Matt Sealey
Top
   
Reply with quote  
frankm
 Post subject:
PostPosted: Wed Nov 16, 2011 1:16 pm 
Offline

Joined: Fri Nov 11, 2011 10:21 am
Posts: 21
Location: Netherlands
Thanks for your reply Matt. I didn't compile it myself, I got it from http://dev.gentoo.org/~darkside/arm/efi ... nstall.xml (the link is on the front page of powerdeveloper.org, under Gentoo), loaded it onto an SD-card and booted from it, then halted the machine by pushing the powerbutton for 5 seconds, on another machine I retrieved dmesg and other logs from the card. All a bit less sophisticated than it may have appeared. Still your reply got me thinking, if it is just the kernel I need to compile I may give it a try, I found some usefull comments, by Marcin Juszkiewicz:
http://marcin.juszkiewicz.com.pl/2010/0 ... compilers/
http://marcin.juszkiewicz.com.pl/2010/0 ... rs-part-2/
http://marcin.juszkiewicz.com.pl/2010/1 ... ntu-10-10/
And Debian's Efika MX page may also be usefull:
http://wiki.debian.org/EfikaMX
What I did not find was a complete recipe for compiling and installing the legacy kernel, is there such a thing somewhere? The above links don't answer all my questions. Should I compile it on the Efika using the headless maverick (which is running fine) or should I cross compile it on an x86_64 maverick (running under KVM on Debian)? What about dependencies? Which gcc version do I need? Is creating the configuration file really as easy as on Debian's page? And there are probably more things that I haven't even thought of.

Hope you, or anyone, can help me on my way,
Frank.
Top
   
Reply with quote  
PurpleAlien
 Post subject:
PostPosted: Wed Nov 16, 2011 2:15 pm 
Offline
Genesi

Joined: Mon Jan 30, 2006 2:28 am
Posts: 409
Location: Finland
Hi Frank,

The following assumes a cross compiler is installed on an x86 Ubuntu system.

You will need:

apt-get install debhelper kernel-package fakeroot binutils-multiarch

Then run something like:

cp arch/arm/configs/mx51_efikamx_defconfig .config
make-kpkg --revision 2011.06 --arch armel --cross-compile arm-linux-gnueabi- --subarch efikamx --us --uc --rootcmd=fakeroot --jobs=2 --initrd TARGET

You can change revision to anything you like.

--arch and --subarch are important.
--initrd is essential. --us and --uc will compile with unchecked ("maintainer mode") and unsigned (i.e. no GPG required) build which means we don't need to go and get ourselves keys.
--cross-compile may not be required at all but some versions of make-kpkg aren't smart.
--rootcmd=fakeroot provides how to gain root acces (normally sudo or fakeroot)
--jobs=2 tells it to use multiple jobs to compile the kernel
TARGET is the output from make-kpkg --targets which is probably going to be best to be "kernel_image" (just linux-image-*.deb), "binary-arch" (linux-image, linux-headers and linux-image_dbg) or "binary" (full suite of packages).


Johan.

_________________
Johan Dams, Genesi USA Inc.
Director, Software Engineering

Yep, I have a blog... PurpleAlienPlanet
Top
   
Reply with quote  
steev
 Post subject:
PostPosted: Wed Nov 16, 2011 5:55 pm 
Offline
Genesi

Joined: Tue Feb 07, 2006 4:49 pm
Posts: 145
Location: San Antonio, TX
I have a gentoo kernel you can attempt to use, the tarball is in my dev space, http://dev.gnetoo.org/~steev/files/2.6. ... mx.tar.bz2 Extract it, and put the files in their proper places. (/boot files go into /boot, /lib/* in /lib/ )

These all assume you have the system running on the internal pata device. If you are running off sdcard, you will need to edit the boot.script file, and assuming u-boot-tools are installed, you just run mkimage -A arm -T script -C none -d /boot/boot.script /boot/boot.scr (as root)

This is running the latest code, although I have commented out a few different comments that would always show up in dmesg.

_________________
Steev Klimaszewski, Genesi USA Inc.
Senior Software Engineer
Top
   
Reply with quote  
frankm
 Post subject: Latest kernel
PostPosted: Fri Nov 18, 2011 11:33 am 
Offline

Joined: Fri Nov 11, 2011 10:21 am
Posts: 21
Location: Netherlands
I compiled the latest legacy kernel, but then used steev's. I copied it to the internal disk, after renaming files and directories that were to be replaced, added siihdm.teneighty=0 siihdmi.seventwenty=0 to boot.script, ran mkimage and booted the new system. Now it does indeed select a 1280x1024@60 mode but, still no display, most of the time. If I plug in the monitor cable while the machine is booting, I get the display working once every ten tries or so but, only in 640x480@59 mode, it selects that mode itself.

I always get this error, in dmesg, whether the display works or not:
mxc_ipu mxc_ipu: IPU Error - IPU_INT_STAT_10 = 0x00080000
and that's right after this:
SIIHDMI: selected configuration:
SIIHDMI: * "1280x1024@60" 108.03 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
If and only if the display does work then further down in dmesg you will see this:
SIIHDMI: selected configuration:
SIIHDMI: "640x480@59" 25.175 640 656 752 800 480 492 494 527 -hsync -vsync

I think I picked the relevant messages but I have no idea what to make of it or what to do about it.

Hope you can make use of it and help me get my monitor to work,
Frank.


Here's the complete dmesg:
Code:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.31.14.27-efikamx (root@zoe) (gcc version 4.5.3 (Gentoo 4.5.3-r1 p1.0, pie-0.4.5) ) #5 Sat Nov 12 21:37:53 CST 2011
[ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Genesi Efika MX (Smarttop)
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 118784
[ 0.000000] free_area_init_node: node 0, pgdat 804843e4, node_mem_map 804ea000
[ 0.000000] DMA zone: 192 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 24384 pages, LIFO batch:3
[ 0.000000] Normal zone: 736 pages used for memmap
[ 0.000000] Normal zone: 93472 pages, LIFO batch:31
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 117856
[ 0.000000] Kernel command line: console=tty1 root=/dev/sda2 rootwait rootfstype=ext4 rw quiet splash siihdmi.seventwenty=0 siihdmi.teneight=0 noinitrd
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 464MB = 464MB total
[ 0.000000] Memory: 465432KB available (3948K code, 599K data, 144K init, 0K highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:368
[ 0.000000] MXC IRQ initialized
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty1] enabled
[ 0.000000] Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] Initializing cgroup subsys ns
[ 0.000000] Initializing cgroup subsys freezer
[ 0.000000] Initializing cgroup subsys net_cls
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] i.MX IRAM pool: 128 KB@0x9d840000
[ 0.000000] IRAM READY
[ 0.000000] CPU is i.MX51 Revision 3.0
[ 0.000000] MXC GPIO hardware
[ 0.000000] Efika MX: mmc0 configured as external SDHC
[ 0.000000] Efika MX: Smarttop Revision 1.3
[ 0.000000] Using SDMA I.API
[ 0.000000] MXC DMA API initialized
[ 0.000000] bio: create slab <bio-0> at 0
[ 0.000000] SCSI subsystem initialized
[ 0.000000] libata version 3.00 loaded.
[ 0.000000] CSPI: mxc_spi-0 probed
[ 0.000000] IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
[ 0.000000] NET: Registered protocol family 8
[ 0.000000] NET: Registered protocol family 20
[ 0.000000] mc13892 Rev 2.0 FinVer 2 detected
[ 0.000000] Initializing regulators for Efika MX
[ 0.000000] regulator: SW1: 600 <--> 1375 mV
[ 0.000000] regulator: SW2: 900 <--> 1850 mV
[ 0.000000] regulator: SW3: 1100 <--> 1850 mV
[ 0.000000] regulator: SW4: 1100 <--> 1850 mV
[ 0.000000] regulator: SWBST: 0 mV
[ 0.000000] regulator: VIOHI: 0 mV
[ 0.000000] regulator: VPLL: 1050 <--> 1800 mV
[ 0.000000] regulator: VDIG: 1650 mV
[ 0.000000] regulator: VSD: 3150 mV
[ 0.000000] regulator: VUSB2: 2400 <--> 2775 mV
[ 0.000000] regulator: VVIDEO: 2775 mV
[ 0.000000] regulator: VAUDIO: 2300 <--> 3000 mV
[ 0.000000] regulator: VCAM: 2500 <--> 3000 mV fast normal
[ 0.000000] regulator: VGEN1: 1200 <--> 3150 mV
[ 0.000000] regulator: VGEN2: 3150 mV
[ 0.000000] regulator: VGEN3: 1800 <--> 2900 mV
[ 0.000000] regulator: VUSB: 0 mV
[ 0.000000] regulator: GPO1: 0 mV
[ 0.000000] regulator: GPO2: 0 mV
[ 0.000000] regulator: GPO3: 0 mV
[ 0.000000] regulator: GPO4: 0 mV
[ 0.000000] Device spi1.0 probed
[ 1.099547] Switched to high resolution mode on CPU 0
[ 1.100898] NET: Registered protocol family 2
[ 1.101224] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.102171] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.102725] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 1.103008] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.103019] TCP reno registered
[ 1.103208] NET: Registered protocol family 1
[ 1.103975] LPMode driver module loaded
[ 1.103987] Static Power Management for Freescale i.MX51
[ 1.104255] PM driver module loaded
[ 1.104486] sdram autogating driver module loaded
[ 1.104786] Bus freq driver module loaded
[ 1.104829] mxc_dvfs_core_probe
[ 1.105077] DVFS driver module loaded
[ 1.105096] i.MXC CPU frequency driver
[ 1.105487] DVFS PER driver module loaded
[ 1.107117] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.107161] msgmni has been set to 909
[ 1.108454] alg: No test for stdrng (krng)
[ 1.108753] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.108772] io scheduler noop registered (default)
[ 1.108799] io scheduler cfq registered
[ 1.132665] Console: switching to colour frame buffer device 80x30
[ 1.760413] SIIHDMI: Device ID: 0xb0 (TPI revision 2.9)
[ 1.763213] SIIHDMI: hotplug: display detached, powered off
[ 1.779025] Serial: MXC Internal UART driver
[ 1.779197] mxcintuart.0: ttymxc0 at MMIO 0x73fbc000 (irq = 31) is a Freescale i.MX
[ 1.784180] loop: module loaded
[ 1.785310] pata_fsl pata_fsl: rchan=29 wchan=28
[ 1.785453] scsi0 : pata_fsl
[ 1.785940] ata1: PATA max UDMA/44 irq 70
[ 1.787264] mice: PS/2 mouse device common for all mice
[ 1.787351] mc13892 rtc probe start
[ 1.800111] pmic_rtc pmic_rtc.1: rtc core: registered pmic_rtc as rtc0
[ 1.800124] mc13892 rtc probe succeed
[ 1.800278] i2c /dev entries driver
[ 1.800818] Linux video capture interface: v2.00
[ 1.801288] mxc_v4l2_output mxc_v4l2_output.0: Registered device video0
[ 1.801476] MXC WatchDog Driver 2.0
[ 1.801588] clk: Unable to get requested clock: wdog_clk
[ 1.801847] MXC Watchdog # 0 Timer: initial timeout 60 sec
[ 1.802149] cpuidle: using governor ladder
[ 1.802161] cpuidle: using governor menu
[ 1.802579] PMIC Character device: successfully loaded
[ 1.803115] VPU initialized
[ 1.803442] mxsdhci: MXC Secure Digital Host Controller Interface driver
[ 1.803499] mxsdhci: MXC SDHCI Controller Driver.
[ 1.803926] mmc0: SDHCI detect irq 128 irq 1 INTERNAL DMA
[ 1.804579] Registered led device: efikamx:green
[ 1.804943] Registered led device: efikamx:red
[ 1.805298] Registered led device: efikamx:blue
[ 1.805707] Advanced Linux Sound Architecture Driver Version 1.0.20.
[ 1.807341] ALSA device list:
[ 1.807352] No soundcards found.
[ 1.808446] TCP cubic registered
[ 1.808459] NET: Registered protocol family 17
[ 1.808533] ThumbEE CPU extension supported.
[ 1.809465] input: Efika MX Input as /devices/virtual/input/input0
[ 1.809984] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
[ 1.810977] regulator_init_complete: incomplete constraints, leaving GPO4 on
[ 1.810993] regulator_init_complete: incomplete constraints, leaving GPO3 on
[ 1.811004] regulator_init_complete: incomplete constraints, leaving GPO2 on
[ 1.811015] regulator_init_complete: incomplete constraints, leaving GPO1 on
[ 1.811029] regulator_init_complete: incomplete constraints, leaving VGEN1 on
[ 1.811041] regulator_init_complete: incomplete constraints, leaving VCAM on
[ 1.811052] regulator_init_complete: incomplete constraints, leaving VAUDIO on
[ 1.811066] regulator_init_complete: incomplete constraints, leaving VSD on
[ 1.811077] regulator_init_complete: incomplete constraints, leaving VDIG on
[ 1.811090] regulator_init_complete: incomplete constraints, leaving SWBST on
[ 1.872815] pmic_rtc pmic_rtc.1: setting system clock to 2011-11-18 11:51:04 UTC (1321617064)
[ 1.963294] ata1.00: ATA-8: SanDisk pSSD-P2 8GB, SSD 5.20, max UDMA/133
[ 1.963311] ata1.00: 15649200 sectors, multi 0: LBA48
[ 2.005706] ata1.00: configured for UDMA/44
[ 2.006087] scsi 0:0:0:0: Direct-Access ATA SanDisk pSSD-P2 SSD PQ: 0 ANSI: 5
[ 2.007194] sd 0:0:0:0: [sda] 15649200 512-byte logical blocks: (8.01 GB/7.46 GiB)
[ 2.007411] sd 0:0:0:0: [sda] Write Protect is off
[ 2.007426] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.007531] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.008475] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.008908] sda: sda1 sda2
[ 2.011342] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.014897] EXT4-fs (sda2): barriers enabled
[ 2.210730] kjournald2 starting: pid 486, dev sda2:8, commit interval 5 seconds
[ 2.210857] EXT4-fs (sda2): warning: maximal mount count reached, running e2fsck is recommended
[ 2.212309] EXT4-fs (sda2): internal journal on sda2:8
[ 2.212327] EXT4-fs (sda2): delayed allocation enabled
[ 2.212339] EXT4-fs: file extents enabled
[ 2.214524] EXT4-fs: mballoc enabled
[ 2.214593] EXT4-fs (sda2): recovery complete
[ 2.216148] EXT4-fs (sda2): mounted filesystem with ordered data mode
[ 2.216214] VFS: Mounted root (ext4 filesystem) on device 8:2.
[ 2.238128] devtmpfs: mounted
[ 2.238285] Freeing init memory: 144K
[ 2.238293] BFS CPU scheduler v0.376 by Con Kolivas.
[ 4.587189] udev[543]: starting version 163
[ 5.120774] usbcore: registered new interface driver usbfs
[ 5.135889] usbcore: registered new interface driver hub
[ 5.185529] sgtl5000-i2c 1-000a: SGTL5000 revision 17
[ 5.199602] usbcore: registered new device driver usb
[ 5.204499] kgsl_hal_init: hal->z430_regspace.mmio_phys_base = 0x30000000
[ 5.204519] kgsl_hal_init: hal->z430_regspace.mmio_virt_base = 0x9d9c0000
[ 5.204530] kgsl_hal_init: hal->z430_regspace.sizebytes = 0x00020000
[ 5.204550] kgsl_hal_init: hal->z160_regspace.mmio_phys_base = 0xd0000000
[ 5.204561] kgsl_hal_init: hal->z160_regspace.mmio_virt_base = 0x9d8fe000
[ 5.204595] kgsl_hal_init: hal->z160_regspace.sizebytes = 0x00001000
[ 5.204918] GPU MMU enabled
[ 5.283721] Reserved memory: pa = 0xae000000 va = 0xa0000000 size = 0x02000000
[ 5.283737] GSL_HAL_MEM2 aperture (PHYS) pa = 0xae000000 va = 0xa0000000 size = 0x02000000
[ 5.283754] GSL_HAL_MEM1 aperture (MMU) pa = 0x00100000 va = 0x00100000 size = 0x08000000
[ 5.351360] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.469653] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 5.469726] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 5.499659] fsl-ehci fsl-ehci.0: irq 18, io base 0x73f80000
[ 5.519618] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 5.537167] usb usb1: configuration #1 chosen from 1 choice
[ 5.570192] hub 1-0:1.0: USB hub found
[ 5.570292] hub 1-0:1.0: 1 port detected
[ 5.789633] usb 1-1: new high speed USB device using fsl-ehci and address 2
[ 5.864090] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
[ 5.864149] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
[ 5.891226] fsl-ehci fsl-ehci.1: irq 14, io base 0x73f80200
[ 5.947802] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
[ 5.956387] usb usb2: configuration #1 chosen from 1 choice
[ 5.994655] hub 2-0:1.0: USB hub found
[ 5.994757] hub 2-0:1.0: 1 port detected
[ 5.995166] No device for DAI imx-ssi-2-0
[ 5.995184] No device for DAI imx-ssi-2-1
[ 6.067959] usb 1-1: configuration #1 chosen from 1 choice
[ 6.341858] usb 2-1: new high speed USB device using fsl-ehci and address 2
[ 6.360652] DMA Sound Buffers Allocated:UseIram=1 buf->addr=1ffe2000 buf->area=9d842000 size=24576
[ 6.360778] DMA Sound Buffers Allocated:UseIram=1 buf->addr=a8588000 buf->area=f9e0a000 size=24576
[ 6.360791] asoc: SGTL5000 <-> imx-ssi-2-0 mapping ok
[ 6.533387] usb 2-1: configuration #1 chosen from 1 choice
[ 6.588433] hub 2-1:1.0: USB hub found
[ 6.588689] hub 2-1:1.0: 4 ports detected
[ 6.920741] usb 2-1.1: new high speed USB device using fsl-ehci and address 3
[ 6.926939] ramzswap: module is from the staging directory, the quality is unknown, you have been warned.
[ 6.987370] ramzswap: num_devices not specified. Using default: 1
[ 7.046468] SIIHDMI: hotplug: display attached, powered on
[ 7.092616] ramzswap: /dev/ramzswap0 initialized: disksize_kb=131072
[ 7.229810] usb 2-1.1: configuration #1 chosen from 1 choice
[ 7.375974] rt2870sta: module is from the staging directory, the quality is unknown, you have been warned.
[ 7.421087] usb 2-1.2: new full speed USB device using fsl-ehci and address 4
[ 7.449749] rtusb init --->
[ 7.580788] usbcore: registered new interface driver rt2870
[ 7.654635] eth0: register 'asix' at usb-fsl-ehci.0-1, ASIX AX88772 USB 2.0 Ethernet, 70:71:bc:9b:98:97
[ 7.758036] usbcore: registered new interface driver asix
[ 7.771052] SIIHDMI: Device ID: 0xb0 (TPI revision 2.9)
[ 7.775206] SIIHDMI: hotplug: display attached, powered on
[ 7.792481] m25p80 spi1.1: sst25vf032b (4096 Kbytes)
[ 7.792500] Creating 3 MTD partitions on "spi_nor_flash":
[ 7.792518] 0x000000000000-0x000000040000 : "u-boot"
[ 7.821426] usb 2-1.2: configuration #1 chosen from 1 choice
[ 7.936573] hub 2-1.2:1.0: USB hub found
[ 7.937871] hub 2-1.2:1.0: 3 ports detected
[ 7.980941] 0x000000040000-0x000000050000 : "config"
[ 8.012029] 0x000000050000-0x000000400000 : "spare"
[ 8.528276] SIIHDMI: Unsupported modelines:
[ 8.528314] SIIHDMI: "1280x1024@75" 135.07 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (pixel clock exceeded)
[ 8.528343] SIIHDMI: discarded 1 incompatible modes
[ 8.528352] SIIHDMI: supported modelines:
[ 8.528368] SIIHDMI: "1280x720@50" 74.250 1280 1720 1760 1980 720 725 730 750 +hsync +vsync
[ 8.528390] SIIHDMI: "1280x720@60" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
[ 8.528410] SIIHDMI: "720x576@50" 27.00 720 732 796 864 576 581 586 625 -hsync -vsync
[ 8.528430] SIIHDMI: "720x480@59" 27.00 720 736 798 858 480 489 495 525 -hsync -vsync
[ 8.528451] SIIHDMI: "1280x960@60" 108.03 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync
[ 8.528472] SIIHDMI: "1152x864@75" 108.03 1152 1216 1344 1600 864 865 868 900 +hsync +vsync
[ 8.528493] SIIHDMI: "1024x768@75" 78.802 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
[ 8.528514] SIIHDMI: "1024x768@70" 75.01 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
[ 8.528534] SIIHDMI: "1024x768@60" 65.02 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
[ 8.528555] SIIHDMI: "832x624@75" 53.433 832 875 962 1092 624 625 628 652 -hsync -vsync
[ 8.528575] SIIHDMI: "800x600@75" 49.500 800 816 896 1056 600 601 604 625 +hsync +vsync
[ 8.528595] SIIHDMI: "800x600@72" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync
[ 8.528615] SIIHDMI: "800x600@60" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
[ 8.528635] SIIHDMI: "800x600@56" 36.01 800 824 896 1024 600 601 603 625 +hsync +vsync
[ 8.528655] SIIHDMI: "640x480@75" 31.500 640 656 720 840 480 481 484 500 -hsync -vsync
[ 8.528675] SIIHDMI: "640x480@72" 31.500 640 664 704 832 480 489 491 520 -hsync -vsync
[ 8.528695] SIIHDMI: "640x480@67" 27.106 640 661 725 810 480 481 484 499 -hsync -vsync
[ 8.528715] SIIHDMI: "640x480@60" 25.200 640 656 752 800 480 490 492 525 -hsync -vsync
[ 8.528735] SIIHDMI: "720x400@70" 26.171 720 737 808 896 400 401 404 417 -hsync -vsync
[ 8.528755] SIIHDMI: * "1280x1024@60" 108.03 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
[ 8.557021] SIIHDMI: selected configuration:
[ 8.557052] SIIHDMI: * "1280x1024@60" 108.03 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
[ 8.699922] IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
[ 8.733277] mxc_ipu mxc_ipu: IPU Error - IPU_INT_STAT_10 = 0x00080000
[ 8.990169] usb 2-1.2.1: new low speed USB device using fsl-ehci and address 5
[ 9.136982] Adding 131064k swap on /dev/ramzswap0. Priority:0 extents:1 across:131064k SS
[ 9.168726] usb 2-1.2.1: configuration #1 chosen from 1 choice
[ 9.285317] usb 2-1.2.3: new full speed USB device using fsl-ehci and address 6
[ 9.323016] usbcore: registered new interface driver usbhid
[ 9.323060] usbhid: v2.6:USB HID core driver
[ 9.389806] input: Mitsumi Electric Apple Optical USB Mouse as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2.1/2-1.2.1:1.0/input/input1
[ 9.390646] apple 0003:05AC:0304.0001: input: USB HID v1.10 Mouse [Mitsumi Electric Apple Optical USB Mouse] on usb-fsl-ehci.1-1.2.1/input0
[ 9.452665] usb 2-1.2.3: configuration #1 chosen from 1 choice
[ 9.581915] input: Mitsumi Electric Apple Extended USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2.3/2-1.2.3:1.0/input/input2
[ 9.603674] generic-usb 0003:05AC:020C.0002: input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-fsl-ehci.1-1.2.3/input0
[ 9.739952] input: Mitsumi Electric Apple Extended USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2.3/2-1.2.3:1.1/input/input3
[ 9.764013] generic-usb 0003:05AC:020C.0003: input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-fsl-ehci.1-1.2.3/input1
[ 9.967058] kjournald starting. Commit interval 15 seconds
[ 9.968749] EXT3 FS on sda1, internal journal
[ 9.968777] EXT3-fs: mounted filesystem with writeback data mode.
[ 10.494793] NET: Registered protocol family 10
[ 10.496381] lo: Disabled Privacy Extensions
[ 11.301865] eth0: link down
[ 11.305953] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.378492] usb 2-1.1: firmware: requesting rt3070.bin
[ 13.153202] 0x1300 = 00073200
[ 13.154717] eth0: link down
[ 13.572669] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 14.251509] SIIHDMI: selected configuration:
[ 14.251543] SIIHDMI: "640x480@59" 25.175 640 656 752 800 480 492 494 527 -hsync -vsync
[ 14.389892] Z430 found: core 0 major 2 minor 5 patch 1 (chipid 0x00020501)
[ 19.977601] 0x1300 = 00073200
[ 23.267498] imx_ssi_irq mxc_ssi SISR fc30 SIER 780500 fifo_errs=1
[ 30.489554] wlan0: no IPv6 routers present
[ 536.570188] usb 2-1.3: new high speed USB device using fsl-ehci and address 7
[ 536.693001] usb 2-1.3: configuration #1 chosen from 1 choice
[ 536.796938] usbcore: registered new interface driver libusual
[ 536.837523] Initializing USB Mass Storage driver...
[ 536.838041] scsi1 : SCSI emulation for USB Mass Storage devices
[ 536.852725] usb-storage: device found at 7
[ 536.852743] usb-storage: waiting for device to settle before scanning
[ 536.853047] usbcore: registered new interface driver usb-storage
[ 536.853084] USB Mass Storage support registered.
[ 4.978950] usb-storage: device scan complete
[ 4.980028] scsi 1:0:0:0: Direct-Access Ut165 USB2FlashStorage 0.00 PQ: 0 ANSI: 2
[ 5.011057] sd 1:0:0:0: [sdb] 3948544 512-byte logical blocks: (2.02 GB/1.88 GiB)
[ 5.011926] sd 1:0:0:0: [sdb] Write Protect is off
[ 5.011944] sd 1:0:0:0: [sdb] Mode Sense: 00 00 00 00
[ 5.011955] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 5.033612] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 5.042320] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 5.042349] sdb: sdb1 sdb2
[ 5.193723] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[ 5.193751] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[ 6.537926] kjournald starting. Commit interval 15 seconds
[ 6.537995] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[ 6.579147] EXT3 FS on sdb2, internal journal
[ 6.579181] EXT3-fs: mounted filesystem with writeback data mode.
[ 203.863369] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 203.867956] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 214.518629] eth0: no IPv6 routers present
[ 279.506517] usb 2-1.3: USB disconnect, address 7
[ 228.540644] usb 2-1.3: new high speed USB device using fsl-ehci and address 8
[ 228.656667] usb 2-1.3: configuration #1 chosen from 1 choice
[ 228.664954] hub 2-1.3:1.0: USB hub found
[ 228.681650] hub 2-1.3:1.0: 4 ports detected
[ 228.970553] usb 2-1.3.4: new high speed USB device using fsl-ehci and address 9
[ 229.090228] usb 2-1.3.4: configuration #1 chosen from 1 choice
[ 229.108595] hub 2-1.3.4:1.0: USB hub found
[ 229.109222] hub 2-1.3.4:1.0: 4 ports detected
[ 271.040646] usb 2-1.3.1: new high speed USB device using fsl-ehci and address 10
[ 271.170768] usb 2-1.3.1: configuration #1 chosen from 1 choice
[ 271.194040] scsi2 : SCSI emulation for USB Mass Storage devices
[ 271.212500] usb-storage: device found at 10
[ 271.212515] usb-storage: waiting for device to settle before scanning
[ 276.211064] usb-storage: device scan complete
[ 276.217082] scsi 2:0:0:0: CD-ROM TSSTcorp CDDVDW SE-S084D TS01 PQ: 0 ANSI: 0
[ 276.310656] sr0: scsi3-mmc drive: 8x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 276.310678] Uniform CD-ROM driver Revision: 3.20
[ 276.327350] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 276.339842] sr 2:0:0:0: Attached scsi generic sg1 type 5
Top
   
Reply with quote  
frankm
 Post subject: Forgot something
PostPosted: Fri Nov 18, 2011 2:10 pm 
Offline

Joined: Fri Nov 11, 2011 10:21 am
Posts: 21
Location: Netherlands
I forgot to mention that when the display does work in 640x480 mode, I first get a black screen and after a short while it presents GDM, before that there are no messages and there is no fancy boot screen, just once, for a fraction of a second, did I see the Genesi logo.

Frank.
Top
   
Reply with quote  
jlpoole
 Post subject:
PostPosted: Mon Nov 21, 2011 10:01 pm 
Offline

Joined: Tue Nov 08, 2011 9:27 pm
Posts: 24
Location: Redwood Shores, CA & Napa, CA
Quote:
I have a gentoo kernel you can attempt to use, the tarball is in my dev space, http://dev.gnetoo.org/~steev/files/2.6. ... mx.tar.bz2...
The correct URL is:

http://dev.gentoo.org/~steev/files/2.6. ... mx.tar.bz2

"gnetoo" and the version incremented. Probably safest to view the folder at: http://dev.gentoo.org/~steev/files/
Top
   
Reply with quote  
frankm
 Post subject: latest kernel
PostPosted: Tue Nov 22, 2011 7:04 am 
Offline

Joined: Fri Nov 11, 2011 10:21 am
Posts: 21
Location: Netherlands
After jlpoole's remark I checked steev's Gentoo directory, he has updated the kernel so, I gave it another trie, same result though.

The new kernel does select a 1280x1024@60 mode but, usually no display. If I plug in the monitor cable while the machine is booting, I get the display working once every ten tries or so but, only in 640x480@59 mode and even then I don't see a boot splash nor any messages only GDM and X.

When SIIHDMI is configuring I always get these messages:
SIIHDMI: selected configuration:
SIIHDMI: * "1280x1024@60" 108.03 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync
IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7)
mxc_ipu mxc_ipu: IPU Error - IPU_INT_STAT_10 = 0x00080000

I had a look at the source code and as far as I can figure out the IPU sends an interrupt with error code
0x00080000, what does that code mean, is the modeline wrong or is it something else?

I hooked up the display (NEC MultiSync EA191M) to another machine, via vga (the monitor has both vga and dvi-d), and checked Xorg's log, it uses the same modeline, also the EDID in the log is identical to the first half of the EDID I retrieved from the Efika MX, except for the checksum. Everything should work unless the EDID is almost correct and the error doesn't matter for vga and does matter for dvi-d. The Xorg log did show one (DDC gathered) modeline that differs slightly from the one used:
"1280x1024"x59.9 109.00 1280 1368 1496 1712 1024 1027 1034 1063 -hsync +vsync (63.7 kHz).

What do I make of this and what does IPU_INT_STAT_10 = 0x00080000 mean?
Top
   
Reply with quote  
PurpleAlien
 Post subject:
PostPosted: Tue Nov 22, 2011 1:27 pm 
Offline
Genesi

Joined: Mon Jan 30, 2006 2:28 am
Posts: 409
Location: Finland
Hi.

Please try the kernel here and see if that changes anything:

http://193.239.210.15/~johan/efikamx/li ... _armel.deb

With this kernel, also try the options "siihdmi.seventwenty=0" and "siihdmi.teneighty=0" to your boot.script


Johan.

_________________
Johan Dams, Genesi USA Inc.
Director, Software Engineering

Yep, I have a blog... PurpleAlienPlanet
Top
   
Reply with quote  
frankm
 Post subject: Problem solved, almost
PostPosted: Fri Nov 25, 2011 12:24 pm 
Offline

Joined: Fri Nov 11, 2011 10:21 am
Posts: 21
Location: Netherlands
Hello all,

Steev and Johan thanks for your kernels, for taking the time to help me solve my display problem, unfortunately it didn't help much, so, as a last resort, I bought a different HDMI to DVI cable, and that did work, I'm looking at a near perfect screen now with beautifull colors (I added "video=mxcdi0fb:bpp=32 siihdmi.teneighty=0 siihdmi.seventwenty=0" to the bootargs). The Efika can even wake the display and put it to sleep. The first cable was by a company named Deltac and the one that does work is made by ICIDU.
Both the vanilla 26 kernel (October release) and the 27 kernel work with my display (NEC MultiSync EA191M) and the new cable however, somewhere the screen is scaled down from 1280x1024 to 1280x1023 resulting in some fuzziness, especially noticeable on the console.

When booting SIIHDMI selects this modeline:
"1280x1024@60" 108.03 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync

Xorg uses this one:
"current"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync -csync (64.0 kHz)

This is the output from:
xrandr --verbose
xrandr: Failed to get size of gamma for output default
Screen 0: minimum 1280 x 1024, current 1280 x 1024, maximum 1280 x 1024
default connected 1280x1024+0+0 (0x10c) normal (normal) 0mm x 0mm
Identifier: 0x10b
Timestamp: 19833
Subpixel: unknown
Clones:
CRTC: 0
CRTCs: 0
Transform: 1.000000 0.000000 0.000000
0.000000 1.000000 0.000000
0.000000 0.000000 1.000000
filter:
1280x1024 (0x10c) 78.6MHz *current
h: width 1280 start 0 end 0 total 1280 skew 0 clock 61.4KHz
v: height 1024 start 0 end 0 total 1024 clock 60.0Hz

This is the output of fbset:
fbset -i

mode "1280x1024-60"
# D: 108.003 MHz, H: 63.983 kHz, V: 60.021 Hz
geometry 1280 1024 1280 3072 32
timings 9259 248 48 38 1 112 3
hsync high
vsync high
rgba 8/16,8/8,8/0,8/24
endmode

Frame buffer device information:
Name : DISP3 BG
Address : 0xad000000
Size : 16777216
Type : PACKED PIXELS
Visual : TRUECOLOR
XPanStep : 0
YPanStep : 1
YWrapStep : 0
LineLength : 5120
Accelerator : No

My display's OSD says:
1280x1023
H 64.2kHz V 60.2Hz

I searched the web a bit and this problem appears to be similar to another one:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=478196
https://bugs.freedesktop.org/show_bug.cgi?id=13968
https://bugs.freedesktop.org/show_bug.cgi?id=15370

I tried to solve this problem by adding "siihdmi.force_dvi=1" to the bootargs, that didn't do anything, neither does removing "video=mxcdi0fb:bpp=32".
I tried setting different modes with xrandr but, it refuses to change anything, what does work, as a workaround is:
fbset -yres 1025
That does produce a perfect picture, albeit a temporary one.

Hopefully someone knows what is to blame here and how to solve it.

Frank.
Top
   
Reply with quote  
Display posts from previous:  Sort by  
Post new topic  Reply to topic  Page 1 of 1
  [ 12 posts ] 

Board index » »

All times are UTC-06:00

Who is online

Users browsing this forum: No registered users and 20 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron
PowerDeveloper.org: Copyright © 2004-2012, Genesi USA, Inc. The Power Architecture and Power.org wordmarks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org.
All other names and trademarks used are property of their respective owners. Privacy Policy
Powered by phpBB® Forum Software © phpBB Group